How to replace bearings in a Beko washing machine

The user will immediately find out that the bearing in the automatic machine has worn out or completely fallen apart. The washing machine will begin to make a “knocking” sound, hum, vibrate and malfunction. To prevent the unit from permanently failing, it is necessary to replace the drum bearing as soon as possible. Timely repairs will preserve the remaining elements and components of the system.

Before you begin replacement, you should understand the essence of the upcoming work. You can change the bearings yourself, without resorting to the help of specialists. We will explain in detail how to do this in this article.

Detection of bearing failures

First of all, I would like to note that in Beko washing machines, in comparison with other brands of equipment, the process of replacing bearings is quite simple, and this is good news. First, let's look at what signs will indicate a 100% need for replacement?

1. A hum that occurs when the drum is rotated by hand.
2. There is significant drum play.
3. In the “Spin” mode, the washing machine makes a lot of noise and knocks.

In some cases, not only bearing wear may occur, but also the crosspiece may break. This situation will lead to higher repair costs, since the part cannot be purchased separately; it is supplied only complete with the drum.

Let's start disassembling the machine

To disassemble the washing machine, you need to prepare a screwdriver, Phillips and flathead screwdrivers. Using these tools, you can remove all parts of the machine and get to the washing machine tank. The algorithm of actions will be as follows:

• disconnect the device from the power supply;
• remove the top cover of the case, and to do this, unscrew the 2 screws located on the back;
• remove the powder receptacle from the unit;
• Unscrew the screws holding the control panel and move it to the side;
  
• unfasten the lower decorative panel from the body;
• unscrew the 3 screws located behind the decorative panel;
• Unclench the wire clamp holding the cuff, move it to the side and tuck the elastic into the drum;
• Unfasten the front wall of the case.
  

When removing the front panel, you will see that the hatch locking device is not disconnected from the main part of the machine. It is necessary to carefully, without damaging the contacts, reset the lock chip or simply unhook the UBL.

• unfasten the filler pipe;
• disconnect the wire leading to the dispenser and disconnect the tray from the body;
• remove the upper metal false panel that opened after disconnecting the control panel;
• lower the counterweight down a little, to do this loosen its mounting bolts;
• disconnect the thermistor by resetting its terminals;
• remove the power and ground wires from the contacts of the tubular heater;
• remove the heating element from the housing;
• loosen the clamps holding the plastic tank cover;
• remove the cover and set it aside.

The main stage of analyzing the SMA has been completed, as you understand, you can do the work yourself, it is not necessary to transfer the washing machine to a workshop. To change the bearings, you have to remove the drum from the housing and gain access to the worn parts.

We take out the drum and remove the old bearings

Further repairs will be made after removing the washing machine drum. You have to loosen the pulley and remove the drive belt. We act carefully.

1. We unfasten the back wall of the Beko washing machine body; it is secured with five self-tapping screws located around the perimeter.
2. Remove the drive belt.
3. Unscrew the nut holding the pulley.
4. Carefully remove the drum from the housing.

At this stage, you should inspect the drum cross for wear. If no traces of it are found on the shaft, repairs can continue as planned. If the crosspiece is in poor condition, you will have to purchase or repair the part, and only then continue working.

You can proceed to the important stage - knocking out the bearings from the tank. To do this you will need a regular hammer and a special drift. The algorithm of actions is quite simple.

1. Remove the oil seal (rubber sealing ring).
2. Place the end of the drift in the center of the rear bearing and tap the metal rod with a hammer.

Be sure to change the direction of the punch, do not hit the same place.

3. Go around the back of the machine and start knocking out the second bearing.

After the parts requiring replacement are knocked out, the tank will look like this:

Now you should clean the seat from liquid, rust, dirt, and plaque. Be sure to clean the drum shaft. After disassembling the drum of the Beko machine, you can press in new bearings.

We install new bearings

To purchase suitable components for the washing machine, you need to know the full name of the automatic machine model. When purchasing bearings, you should provide this information to the manager. Another option is to contact a specialized store with the elements already removed and ask specialists to select identical parts.

A bearing of a smaller diameter is installed on the outside of the tank (this can be done through the removed rear wall of the housing). It is hammered in with a hammer and a drift. You should rest solely on the outer frame of the part and, tapping with a hammer, carefully press the element inside the tank.

Do not hit the inner race of the bearing under any circumstances, as this may lead to its destruction.

Having attached one of the parts, you can proceed to installing the second element. To begin, insert the bearing into the hole and fix its position with one blow of a hammer.

Then, using a drift, hammer the element into place. After installing the bearings, it is necessary to “plant” the oil seal in place. The rubber ring is treated with a special lubricant, this is necessary to improve performance characteristics and extend the service life of the seal.

After the oil seal is securely fixed, it is necessary to treat the drum bushing with a lubricant. Lubrication will ensure water tightness and heat resistance of the connection, extending the life of the bearings and sealing ring.

The replacement has been made, now it is necessary to put all the elements of the system into the housing. First of all, the drum is installed in place, the pulley is attached, and the drive belt is put on. Next, the rear wall of the unit is screwed into place. Subsequent assembly is carried out in reverse order. As you can see, it is possible to replace bearings with your own hands. To do this, you need to prepare all the necessary tools and strictly follow the instructions for action.

Reader comments

• Share your opinion - leave a comment