All about washing machines

How to install a washing machine in the bathroom yourself

How to install a washing machine in the bathroom yourselfThe proper functioning of the AGR is largely dependent on the correct installation of the unit. It is important to correctly select the location of the device, carefully study the instructions for connecting the machine to house utilities. Most often, users want to install a washing machine in the bathroom, because this place seems to them more convenient for the further operation of the washing machine. This room is characterized by high humidity, therefore, certain rules must be observed when connecting the unit.

Choose a place carefully

Before you independently connect the machine in the bathroom, you should determine the specific place where it will be installed. Despite the size of the room and its design, when choosing a site for SMA, some conditions should be observed.

  1. The unit should be located as close as possible to the house communications. This will allow you to easily connect the drain and water intake hoses. Of course, you can extend the hoses if necessary, but this will entail additional costs of money, effort and time.
  2. The machine must be placed near a power outlet so that the power cord of the device can reach the connection point without problems.Place the washing machine in the bathroom Using an extension cord is extremely dangerous; it can cause electric shock to the user.
  3. A lot of splashes, drops, steam should not get on the walls of the machine case. The technique is not afraid of high humidity, but if you constantly water it with water, the washing machine will certainly fail.
  4. No foreign objects can be installed on the unit, all this is an additional mechanical load that disrupts the normal functioning of the device and leads to equipment breakdown.
  5. The wash should not limit free movement in space. Firstly, it will bring inconvenience to family members, and secondly, it will increase the risk of causing mechanical defects to the body of the machine.

When the room is spacious enough, then there should be no difficulties with choosing a place for mounting the machine. Under it, you can select any of the free corners or an unoccupied part of the wall. In modern interiors, a separate niche is often the place to install the machine.

If the bathroom is modest in size, you can place the SMA directly under the countertop with a sink, or under a sink called a “water lily”. A washbasin of such an interesting shape will not go beyond the unit body, thereby saving space in the room.

Getting ready for the installation process.

Choosing a place for a washer, it is necessary to analyze the walls and floor in this area, they should be strong and straight. Reliable, dry and even surfaces will provide the necessary conditions for the normal functioning of the AGR. Damp walls will adversely affect the body of the unit, causing corrosion of the metal elements of the machine.

It is very important to pay attention to the flooring, an uneven floor provokes increased vibration of the washing machine during operation, and, therefore, increased wear of all elements of the system.

Set the machine by levelSo what do you need to check? First, the plane is examined for cracks, chips, voids. Secondly, the surface is checked using a building level. If there is mold in the seams between the tiles, be sure to treat the area with special antifungal agents.

At this stage, it is recommended to consider how the unit will be connected to the water supply and sewage engineering system, and measure the length of the hoses. It is very important to carry out all measurements accurately, so that the washing machine "fit" in a clearly defined place for it.

Increased attention should be paid to the preparation of the electrical point that feeds the machine. The outlet for the washing machine must have a grounding and protection against moisture, it is necessary to put a three-wire device at 16 Amps. Connect the point directly to the shield, it is best to provide for it a circuit breaker. For added security, it’s better to use voltage regulator for a washing machine.

The next step is the organization of communication outputs. Their device directly depends on the chosen method of connecting equipment, familiarize yourself with the available options and choose the most comfortable and acceptable for your case.

We are connected to the water supply

There are several ways to carry out this procedure. The choice of connection option will depend on the skills available for the person installing the washer. Consider the communications to which you will be connected, if there is a need, it is better to replace them before installing the machine. We will analyze the main methods by which you can connect the unit to the water supply.

If the pipes are old steel

Metal pipe connectionUnder such conditions, it is necessary to insert directly into the water pipe. For this, a mortise clamp or a special crimp sleeve is used. At the top of the element there is a threaded cavity where the hose for the intake of water from the CMA will be attached.

In addition, a guide sleeve and a rubber gasket in the shape of a rectangle can be found with the coupling. The insert is performed as follows:

  • close all faucets of the mixer and the valve blocking water supply;
  • surface of communications, where the gasket will be located, clean and grind to smoothness;
  • insert the guide sleeve into the mortise clamp and fix it in the cutout of the rubber gasket;
  • amass the clamp on the water pipe with 4 bolts, tighten each of them one at a time so that the elastic is pressed very tightly;
  • Using a drill with a drill from 6 to 8 mm in diameter, make a hole in the pipe wall.

Place a small container under the clamp and slightly open the mixer, this will allow the water remaining inside to spill out.

When liquid spills out, carefully clean the hole from metal chips, secure a new tap and examine the system for leaks. If the communications are not made of metal, but of metal plastic, a special element is used instead of the mortise clamp - a tee fitting. The procedure will be even easier: blocking the water in the riser, just outline the connection point, cut a piece of metal plastic. In the resulting opening, insert the fitting with integrated rubber bands and attach the ball valve.

Connect to the mixer inlet

Mixer connectionThe following method requires the user to place a special feed tap between the eccentric and the mixer. This tap is understaffed with a hose extension to the hot water system. This method is very popular due to its simplicity, work is carried out quite quickly. However, all tubes and hoses are located in plain sight, due to which the aesthetics of the interior are violated.

Manipulations on a mixer made according to European standards can be done in a few minutes. For this:

  • disconnect the hose responsible for the supply of cold water;
  • screw on the eccentric tap made in the shape of a tee;
  • in one of the holes, turn on the mixer hose, in the second - the machine inlet hose.

If the mixer on your bath is from a domestic manufacturer, then the algorithm will be a little different. When disconnecting, unscrew the cam and install a globe valve equipped with a special extension.

We connect the inlet hose to the mixer or tank

This method is the most practical and often used. Faucets are displayed on the finished connections, which are used to withdraw fluid to the toilet flush tank, water heater or mixer.The outlet for the washing machine is mounted between the water riser and the faucet for the tank or mixer.

When connecting the element in the zone of the water heater, make sure that the check valve is placed between the pipe and the valve, otherwise you will not be able to start the wash when the hot water supply is turned off. The inclusion algorithm will be as follows:

  • block cold water;
  • twist the crane responsible for its supply;
  • take a tee crane, wrap the external thread with FUM-coy;
  • screw the part instead of the removed one;
  • connect the hose from the mixer to one hole, the intake hose of the machine to the second.

Doing it yourself is not difficult, the main thing is to carefully study the basic installation rules, strictly follow the algorithm of actions stated in the instructions. Do not forget about safety precautions.

Drain organization

Draining waste water from the tank is one of the main functions of any SMA, therefore it is very important to provide the drain pump with the ability to clean the machine of excess water. The pump must, without additional loads, calmly dispose of the spent fluid in such a way as to avoid its return to the unit system. To do this, properly connect the washer to the sewer.

Simple sewage discharge

Direct sewage discharge to the bathroomThis method is the simplest, however, not entirely user friendly. The principle of operation of the drainage system in this case will be primitive: one end of the hose is attached to a special hole on the machine body, the other goes to the sink, bathtub or toilet bowl.

The advantages of this method are one - minimal time and effort. Cons, on the contrary, are many. Firstly, the drain hose is not securely fixed, so there is a chance that it may fall and fill the room with dirty water. Secondly, during the washing process, you can not use plumbing. Thirdly, the waste liquid contaminates the surface of the bathtub and sink, such a method of discharging water is unhygienic.

We connect to the side fitting of the siphon

If the washing machine is located in close proximity to the washbasin, the drain pipe can be connected to a siphon. An ordinary siphon will have to be replaced with a special one equipped with an additional nozzle. Then just the tip of the washing hose is attached to the nozzle. The outlet is at the top of the structure and at a slight angle, so the wastewater from the sink will not get into the drainage system of the machine.

If we talk about the disadvantages of this method, there are two of them: the possibility of unpleasant odor from the sewer system entering the machine’s tank (it is recommended to use a water seal to avoid this), and the likelihood that, with an excessively strong pressure, the waste water will not go into the sewer, but will rise into the sink and overflows over the edges.

Connect to the sewer directly

This method, although it is the most laborious, is significantly superior in reliability to the previous ones. What needs to be prepared? A tee of the desired diameter, having an oblique tap and a check valve for the SMA. One part of the valve is connected to the drain pipe, the second, through a tee-tap, is attached to the sewage system.

Direct connection to the sewer pipe

The inlet for the drain hose should be at a slight angle and be located from top to bottom, this will avoid getting into it drains from the plumbing, which can spread a nasty smell.

Installation Description

To begin with, the AGR needs to be freed from the manufacturer’s packaging, remove the locking bolts that prevent the drum from loosening during transportation. It is very important not to forget to pull out the stoppers, they can lead to failure of the undercarriage. Unscrew the bolts using the open-end wrench. They are pulled out of the washer housing along with the bushings, and plugs specially provided for this are inserted into the holes formed.

The locking bolts must be kept during the warranty period of the machine, as well as in case you need to transport the unit for personal purposes.

  1. Put the AGR in the selected place, put the level on the upper wall of the body. If the equipment is uneven, it should be adjusted according to the level of its legs. There is no need to put the washing machine close to the wall, as well as furniture and plumbing, if they are on the sides of the unit, be sure to leave a small gap.
  2. Pull the automatic machine forward a little, this will facilitate the procedure for connecting it to communications.
  3. Connect the drain and water inlet hose to the house utility networks by selecting any of the above methods.
  4. Fill all hoses into specially provided recesses of the washing machine, this will eliminate their bends.

After carrying out all the actions, the unit moves to its original position, is installed in a constant place, is once again regulated in level. In the end, it remains only to connect the machine to the network and check its performance by running a test mode.

First start

When launching a test program, be sure to take the technical data sheet of the device and keep it in front of you. It will be needed for data verification. A trial run does not involve loading laundry into the drum; it only happens with water and detergent.

First, water is taken into the SMA tank. It is necessary to note the time of filling the drum to a certain point. Be sure to inspect the system for leaks, and if they are found, drain the fluid and carry out work to seal the problematic joints. If there are no emergency leaks, check the unit further. Water heating to the indicated temperature should occur in 5-7 minutes. Check the measured time with that specified in the technical data sheet.

During normal operation, the washing machine should perform all operations silently, incomprehensible squeaks, knocks or rustles at the stage of heating the water indicate a malfunction in the system.

If the machine is functioning properly, almost silently, carry out a test check further, explore other functions and capabilities of the washer, including the performance of the drain system. At the end of the mode, once again look at all the pipes, joints, walls, flooring around the device - everything should be dry.

Possible problems

It happens that after a test wash all the connections and tubes of the device remain dry, but there is water on the floor. This can happen if the dust filter is not fully screwed in. It is located below the machine, behind the false panel or in a special hatch for the trash filter. By fixing it more tightly, you can get rid of such a problem.

If the washing machine vibrates, rattles and sways when working in the “Spin” mode, it may be installed unevenly, or the problem is in the wrong flooring. Another reason for this may be poorly fixed balances. If the machine is new, then it is better to call a specialist to eliminate factory defects, but when the warranty period has already expired, you can tighten the counterweight bolts with your own hands by removing the top cover of the case.

If all installation rules have been followed and the washing machine gives serious errors, for example, it doesn’t turn on, doesn’t start washing, doesn’t adjust the parameters of the selected mode, it’s better not to “go deep” into the unit and find out the reasons for this, but hand the machine over to the service center for a warranty card .

   

Reader Comments

  • Share your opinion - leave a comment

Add a comment

Read also

Error codes for washing machines