Hans's washing machine - error codes
In this post, we will discuss the errors of washing machines from the manufacturer Hansa.
And also how they are displayed.
And so we go straight to the topic.
PC typewriter errors
Codes | The causes of the malfunction and what happens next | Why did the error happen? |
E01 | Error with the designation E01. There is no notification that the UBL (locking device for the hatch of the washing machine) is turned on. | The causes of this malfunction:
|
E02 | Error E02 has occurred. Water is too slowly pouring into the washing machine or there is no gulf. | What caused the error?
|
E03 | Display error E03 Water is draining too slowly from the washing machine tank. Or does not merge at all. | Why did the error appear?
|
E04 | An error has appeared under the code E04 The level sensor informs that the tank of the washing machine is filled with water to the maximum. | Why did a malfunction occur?
|
E05 | E05 lights up Filling the washing machine tank too slowly with water. Or lack of filling (filling for more than 10 minutes). | We will understand the reasons:
|
E06 | Error E06 occurred. Water drains too slowly or does not drain at all (waiting for draining for more than 10 minutes). |
|
E07 | There was a leak. Water appeared in the pan of the washing machine. Activated Aquastop. |
|
E08 | Power failure | It is necessary to check the power supply parameters. |
E09 | Too much foam appeared in the washing machine during the push-up process. | Most likely, too much detergent was used. Or, a tool not intended for machine washing was used. |
E11 | UBL simistr does not work. | The controller may have malfunctioned or broken. |
E21 | The electric motor of the washing machine is blocked. There is no response from the tachogenerator. |
|
E22 | The engine works despite the fact that he was not given a command to work. | Probably shorted triac electric motor. |
E31 | Shorted temperature sensor | The temperature sensor or its wiring has shorted out. |
E32 | The temperature sensor circuit is broken | Probably there was a violation of the integrity of the temperature sensor circuit. |
E42 | The washing is over, the door lock of the washing machine does not turn off. More than 3 minutes have passed. | Such a malfunction can occur due to breakage of the hatch lock, locking of the door or failure of the controller. |
E52 | Violation of the work of volatile. memory cars. | The malfunction occurred due to a data failure or a breakdown of the volatile circuit. memory controller (you need to change the controller or EEPROM circuit). |
Errors of typewriter models RA
Code | The causes of the malfunction and what happens next | Why did the error happen? |
E01 | UBL does not work (sunroof locking device).After a couple of seconds, the inscription "E01" appears. The washing process stops. |
|
The limit switch does not function. After ten seconds, “E01” appears on the display. The washing stops. |
|
|
E02 | Three minutes after the command to fill the tank of the washing machine with water, there is no message that it has reached the required level. After seven minutes from the moment the command to fill, the washing process stops. |
|
E03 | Three minutes after giving a command to carry out water from the washing machine, there was no message from the level sensor that the water was removed from the tank. UBL keeps the hatch in the closed position until the machine is turned off. |
|
E04 | The level sensor informs that the tank is filled to the maximum with water. The washing process stops. The drain pump starts. After 2 minutes after all the water has been drained, the drain pump will turn off. The hatch lock keeps the door in the closed position until the washing machine is turned off. |
|
E05 | Shorted the temperature sensor or a broken circuit. After a couple of seconds, a message appears indicating that an error has occurred. Washing will be done to the end, but with cold water. |
|
-||- | The water in the washing machine has less than four degrees. An error appears on the display. Washing continues with cold water. |
|
-||- | The water in the machine did not warm up to the set level during the time period set for this. The error is displayed. Nevertheless, washing occurs to the end. |
|
E06 | Not applicable | Not applicable |
E07 | The tachogenerator does not report that the washing machine motor is running during the washing process. The engine restarts three times. If it does not work, washing stops and error information appears on the display. |
|
E08 | There is no message from the tachogenerator during the spin-up. Then the motor turns off, and then the engine restarts three times. If, despite this, it does not work, an error message appears. |
|
E09 | Not applicable | Missing |
Interesting:
Add a comment Cancel reply
Headings
Washing machine repair
For buyers
For users
Dishwasher
Tell me what trouble? Hans's machine displays p10 on the screen.
How to remove the error E01 on Hans Comfort?
What does the p13 code of the Hansa washing machine Fqua Spray 900 comfort aa class mean?
Tell me, error E35 what does it mean? Is there no such instruction?
Tell me, the Hans machine produces an error E10.
Spin stops at 0.08 and then does not gain momentum, the time sensor shows all 0.08.