Zanussi washing machine fault repair
Automatic washing machines produced under the Zanussi brand have always been distinguished by their high quality and low price. However, due to long-term use, due to the fault of the consumer or due to manufacturing defects, the machines break down and require repairs. Repairing Zanussi washing machines should begin with studying their weak points, or rather the most common breakdowns, which is what we will do in this article.
Overview of typical breakdowns
As already noted, repair of Zanussi washing machines should begin with typical breakdowns. Most models of such washing machines are quite demanding on water quality. AND The most common consumer mistake when purchasing and installing Zanussi equipment is connecting it directly to the water supply. The water in the tap is far from being of the highest quality, and we are not just talking about hard water; often rusty water with all sorts of debris flows from the tap, which very quickly clogs the filters of the washing machine.
Important! When installing a Zanussi machine, some craftsmen specifically remove the filter from the inlet valve. This is strictly forbidden, because dirty water can literally destroy the machine from the inside.
Hence the first typical reason for the failure of a Zanussi washing machine is clogged filters. In addition, these washing machines are equipped with extremely unsuccessful hatch locking devices. According to experts, this is one of the most common breakdowns. In this situation, both the mechanism itself and the sensor break down.
As with any other automatic washing machine, the heating element breaks in the Zanussi technique.One of the main reasons for such a breakdown should be considered hard water, although some experts also talk about unsuitable materials from which the heating element tube is made. They say that this metal attracts scale even more. And finally, the last weak point of Zanussi washing machines is the drive belt. It is recommended to check the belt at least once every 4 years and, if necessary, tighten it or change it.
Be sure to clean the filters
Periodically, all washing machine filters need to be cleaned; if this is not done for some time, you may encounter a problem. If there is a blockage in one of the washing machine filters, the household appliance either does not have the ability to draw water for washing or does not drain it. Specifically in Zanussi washing machines, the first option is more common. What can you do?
- Unscrew the inlet filter located on the water pipe and clean it.
- If the inlet filter was not installed, it means that a blockage has formed on the inlet valve filter (in the place where the inlet hose connects to the machine). Remove the top cover of the washing machine and unscrew the inlet valve and filter.
- We unscrew the filter and thoroughly wash its cuff and mesh from dirt, then twist the filter with the inlet valve and put it in place, then close the top cover of the machine.
The “delicate” inlet filters of the Zanussi washing machine create many problems, but they protect the internal units from damage due to the ingress and accumulation of foreign objects and debris brought along with water. Experts recommend installing an inlet filter with a water softening cassette directly onto the water pipe.
Dirt in the washing machine can accumulate not only from tap water, but also from clothing.Not only sand and pieces of dirt get into the machine with clothes. Seed peels, coins, hairpins, and buttons settle in the drain filter. All this can stop the machine from working at once. Experts recommend doing it every time after 2-3 washes. clean the drain filterwithout allowing it to become littered.
Note! Before washing, be sure to check the pockets of the items you put in the Zanussi machine drum; foreign objects can damage the internal parts of the “home assistant”.
The hatch locking device has failed
The device that blocks the hatch of a Zanussi washing machine may break due to careless handling by the user, a manufacturing defect, or due to wear and tear. The main problem arises with the response part of the device. Its plastic part, which holds the plates, is quite “flimsy” and breaks if you close the hatch very suddenly and forcefully. In this case, the hook remains intact, since it is made of metal, and the locking device breaks, making washing impossible. How to fix a breakdown yourself?
In this case, it is almost impossible to repair the device blocking the hatch; it will have to be replaced. Its average cost is about 30 USD. It’s quite expensive to purchase such spare parts for future use, so you first need to remove the old device to be 100% sure of its malfunction, and only then “go shopping.” How to remove the old device?
- Open the hatch cover wide open.
- To the right of the hatch there is a hole for the locking hook and two screws holding the hatch locking device; they must be unscrewed.
- Next, we pry up and remove the clamp holding the hatch cuff (a large elastic band located around the washing machine hatch).The easiest way to pry the clamp off is with a screwdriver, because it is quite thin and fits tightly, so you can’t pry it with your fingers.
- After removing the clamp, take out the cuff itself. You need to pull it out with your fingers.
- We put our hand between the front wall of the washing machine and the edge of the drum and take out the locking device.
- We inspect it visually, make sure that the plastic part is broken and the records have popped out, pack up and go to the store with the old device.
- We show it to the seller, purchase the same new one, come home, and install it in place of the old one. Problem solved!
Note! “Hit” every time by 30 USD. This is a costly affair, so handle your Zanussi washing machine as carefully as possible. It is better to close the hatch carefully, and then press its edge until it clicks, this way a careful and safe fixation of the hatch cover is achieved.
The heating element has burned out
Heating element is the weak point of all washing machines that have to work in conditions of using water with a high content of mineral salts. Some companies are trying to protect the heating elements of their cars using special polymer coatings. For example, about five years ago the Samsung company announced heating elements with a polymer coating that supposedly repels scale. Their idea failed miserably, since scale formed on their heating elements in the same way as on others, without coating.
If the heating element of the washing machine breaks, the water in the tank stops heating, and the system may display error E05. In washing machines The Zanussi heating element is located at the back of the tank, so to get to it you will need to remove the back wall. We first need to check the heating element for functionality; if it does not work, then it must be removed and a new unit installed.How it's done?
- We unscrew the bolts holding the back wall of the washing machine body and remove it.
- In the lower part, right from the tank, two contacts will stick out, from which wires come - this is the heating element.
- Take a multimeter and check the resistance of the heating element; if the device shows zero, you will have to change the heating element.
- There is a nut between the contacts of the heating element; it needs to be unscrewed.
- Remove the wires from the heating element.
- Carefully remove the old heating element from the groove. It may be difficult to do this, since it has become attached over time.
- Spray WD-40 lubricant into the crack to the right and left of the contacts and pull out the old heating element with a rocking motion.
- Through the hole formed, remove all the scale and dirt that you can reach and do not forget to wipe the edges of the hole with a clean cloth.
- Carefully insert and screw the new heating element and connect the wires to it.
- We install the back wall in place and check the operation of the washing machine.
Important! Buy only original heating elements made specifically for the desired Zanussi washing machine model. There is a risk that an unsuitable heating element will burn out, “taking” the control unit with it, and repairs will become even more expensive.
Drive belt problems
“Symptoms” of problems with the drive belt are expressed in the motor running, but the drum not rotating. Washing, as you understand, is impossible. The hum of the engine cannot be confused with anything, but you shouldn’t force it to idle once again. What should you do if there is a problem with the drive belt?
- First, let's inspect the location of the problem by removing the back wall of the washing machine.
- In the opened niche we will see a large round drum pulley, on which the belt is put, and below there is a small engine pulley, on which the drive belt is also put.
- If the belt is in place, but does not rotate the drum pulley, it means that it has exhausted its service life and needs to be replaced. If the belt comes off, you just need to put it back in place.
- We put the belt on the pulleys, put the back wall in place and check the operation of the washing machine.
To summarize, we note that the Zanussi washing machine, despite its reliability, has several typical faults that consumers encounter most often. These are clogged filters, a broken hatch locking device, a burnt heating element and an expired drive belt. If you have a washing machine of this brand, you should have an idea of how to troubleshoot the listed faults.
Interesting:
12 reader comments
Add a comment
Categories
Washing machine repair
For buyers
For users
Dishwasher
The smell of burnt wire, plastic or circuit board, black soot near the hole in the UBL hook.
There is a loud noise when revving up...
The water supply does not stop.
There are no signs of life in my machine, there is no electricity.
Does the machine have a fuse?
The machine fills with water and immediately drains, the display shows E30.
The drum drive belt falls off.
The water and electrics are turned on, the lights are on, but the car does not spin.
After switching on, the engine starts running for a few seconds, after which the car starts to power down.
Konstantin, what was the reason for the lack of signs of life in the machine? I have a similar problem.
The water supply does not stop even when the drum rotates.
The water supply does not stop even when the drum is running. Tell me what to do? It's only been a month since the warranty expired.