Repair of malfunctions of the Indesit washing machine by yourself
Indesit washing machines, like any other brand, have their own design features. These features, on the one hand, give many models advantages over competitors, on the other hand, they cause typical breakdowns that consumers have to face. As part of this article, we will investigate typical malfunctions of Indesit washing machines and consider how to fix them with our own hands.
Frequent breakdowns
The vast majority of Indesit brand automatic washing machines cannot be called super reliable. Leading service centers in the world provided information on the basis of which it was possible to prepare statistics on the number of people contacting with breakdowns of washing machines. Based on the data presented in the graph below, we can conclude - cars Indesit is the most commonly breaking brand.. They find themselves in service centers in the first five years of operation more often than German and Korean equipment.
Why it happens? What are the most common causes of a malfunction? Based on the same statistics, we were able to significantly narrow our search and highlight a number of the most common causes of breakdowns of any Indesit washing machine models. These malfunctions occur in 78% of cases of contacting service centers. What breaks most often?
- A heating element. Ten breaks very often, and this is a common breakdown for all automatic washing machines. But in Indesit machines, the heating element consists of stainless steel without any coating (as, for example, in Samsung machines), so the scale deposits on it twice as intensively.
- Network filter. Also far from the strongest part in the Indesit washing machine. Sometimes even lots of Indesit machines with defective surge protectors come across. On average, such parts burn in the first 3-4 years of operation of the equipment. The benefit of the repair is easy to do with your own hands.
- Bearings. Moving elements of the Indesit washing machine do not break more often than similar models of competing machines, however, this breakdown still occurs quite often. Changing bearings is not a problem - the problem is getting to them. Therefore, in general, bearing repair can be considered difficult.
- Control block. This is truly the weakest link in all Indesit washing machines manufactured before 2012. In the latest models, especially those released in 2014-2015, modernized control units were used, which experts consider more reliable. However, they also need a fairly frequent repair.
- Motor sensor Another weak point of most Indesit washing machine models. The engines themselves are relatively reliable, but there are often problems with their electrics. More precisely, most often capacitors burn. Capacitor repair is not possible - just a replacement.
Note! We deliberately did not include contaminated filters, hoses, etc. into some of the most common breakdowns; these problems are characteristic of all washing machines, not just the Indesit brand.
Breakdown Search Algorithm
Before you start repairing the washing machine with your own hands, you need to find the cause of the malfunction. An independent search for a breakdown in the Indesit washing machine must be carried out according to a clear plan. Only in this case can one be more or less likely to count on success. Act in stages.
- If the washing machine has a display, pay attention to the error codes that pop up on it. The washing machine is designed so that in most cases it can itself diagnose the problem. Decrypt error codes your Indesit and draw conclusions.
- If there is no display or the machine does not give an error code, take a closer look and listen to the device. In particular, in the event of a bearing malfunction, the Indesit washing machine will operate very noisily, especially when the drum rotates at high speed.
- If there are no external signs of damage, you have to climb inside.The easiest way to remove the surge protector, but harder to get to the bearings.
- Take a multimeter and ring all the contacts, wiring and sensors for lack of power. Visually inspect all indoor units, a breakdown will certainly give itself away.
Important! Before disassembling the Indesit washing machine, examine its structure and the layout of the fasteners. For the sake of fidelity, photograph or film each stage of disassembly so as not to forget anything.
Damage to the line filter, motor sensor or heating element
Problems with the contacts of the line filter occur due to high humidity. Unfortunately, the manufacturer still has not solved the problem of their protection, so surge protectors often fail not because of a power surge, but because of banal condensation. Finding an Indesit washing machine surge protector is easy. It is located on the opposite end of the power cord from the outlet. You can dismantle it by removing the top cover of the washing machine and unscrewing one screw holding the device.
You cannot fix the surge protector, you have to change it. Yes, and this is not a problem, you can go buy a new one, put and put the machine into operation. But the trouble is, no one will guarantee that this new surge protector will work for a long time. We give a life example. Indesit, the desperate owner of the washing machine, contacted our service center and said that he changed the power filter three times on his own, but after 4-5 months it burned, and he had to install a new one again.
Checking the mains, network wire and contacts did not give any results - everything turned out to be normal. The technician, assuming that the problem was in high humidity, installed a new surge protector, and filled its contacts with silicone sealant, doing the same with all other suspicious contacts. As a result, the machine has been working properly for 1.5 years now - the problem has been solved.
Note! Before applying the sealant, dry the contacts, strip them and wipe them with a dry cloth, and then cover with a waterproofing layer.
You can talk about a serious problem if the capacitor on the engine of the machine burns. This problem is best eliminated with the help of a professional wizard, because only he can competently “diagnose” and correct such a mistake. Since this problem can easily be confused with a malfunction of the motor.
In contrast to the problem with the engine sensor, a malfunction of the heating element can be detected and repaired by oneself.
- In the vast majority of cases, the machine itself warns of a failed heating element, giving an error code F07
- If this does not happen, then we can understand that the heating element does not warm by indirect signs: the powder does not dissolve, the laundry does not stretch well, the hatch of the washing machine is very cold.
- Having determined the problem, we take a screwdriver and remove the back wall of the washing machine. In the bottom of the tank of the Indesit machine, we find two contacts sticking out of its wall - this is the heating element. We check the voltage with a multimeter. Unscrew the fastener in the middle, pull out the sealing gum, pull out the heater.
- If the ten is covered with a thick layer of scale and there are dark burning spots on it, it should be discarded - the ten is defective. Have to buy and put a new one. Installation and assembly are performed in the reverse order.
Problems with bearings or control unit
Bearing repair is the most difficult. The main problem is not even the disassembly of the washing machine, but the disassembly of the tank itself, because the manufacturer made sure that this unit was a complete structure and could not be repaired. But, as the saying goes, “a ruse for inventions is cunning,” the craftsmen solved this problem by simply sawing the tank in half along the weld.This is a unique and very correct solution, it allows, on the one hand, to get to the faulty elements inside the tank, and on the other, to save a lot of money.
You can replace the bearings of the Indesit washing machine using the information provided on our website. We note immediately that doing it yourself without a suitable tool and proper dexterity is quite difficult. But if you try, you will succeed.
Repair of the control unit of the Indesit washing machine in 90% of cases comes down to replacing the contacts. The control unit in typewriters of this brand is not well protected from moisture, which leads to contact with condensate. The contacts naturally close, and the control unit fails. In theory, it is not difficult to repair the unit, in practice you have to work pretty hard with a multimeter, ringing all the contacts in turn, and even not once, before you can detect a malfunction.
Faulty contacts should be replaced immediately. Stripping in this case is not acceptable. After replacing the contacts it is best to fill with sealant.
To summarize, we note that you can repair your Indesit washing machine yourself in most cases, but not in all. Therefore, to avoid even more serious damage, contact the master, especially if you do not have basic skills in repairing household appliances and are not confident in your abilities. In the end, everyone should do his own thing!
Interesting:
Add a comment Cancel reply
Headings
Washing machine repair
For buyers
For users
Dishwasher
Water is flooded, the engine turns on, after a short pause the pump turns on and works like a washing engine
After washing, the machine does not go into rinse mode, the pump does not turn off.
No drain.
Indesit wisl62 just does not turn on, the indicator light does not light. How to eliminate or what to call? Thank.
Tach sensor on the engine.
He starts to wash in cold water, then heats up after a while, what's the matter?
Water is poured and immediately discharged, before that the drum did not arrive at all, it turned to dry.
water is poured and immediately drained
Try to raise the drain hose above 70cm above the floor.
When water collects and immediately drains, the hose was not fixed at the top point on the back wall (there are clamps), i.e. was below 70 cm from the floor - fixed - everything worked as it should!
Water is poured, the drum spins, the water merges itself, does not go to other modes. What to do?
The machine fills with water, discards and starts to dry dry, the washing mode does not turn off. I have to stop, turn on the reset mode. The rest of the operations are performed sequentially (rinsing and wringing, off).
Hello. We bought an indesit washing machine 03/19/16. installed 03/25/16. They started the program, it stretched, it began to drain the water and went out. They took them to the Expert store where they took them. They say we will not change the luck for examination. Yesterday they called and said that a breakdown had occurred, allegedly because of my fault the module of the machine with the cost of 7000 and the work of 1000 was flooded, they would not do under guarantees.
Changed the lock, the washing machine does not start
The machine works, erases 1 wash, drains and that's it. Those. it does not flush and does not wring out, there is no noise, sparks in the motor area when it turns to the right and left. Everything is fine. What to do?
Change the brushes ... On the engine ...
After switching on after 10 minutes, the operation stops, the clicks of the relay are audible.
The machine launches and shuts down, i.e. does not rinse and does not squeeze.What's the matter?
The machine launches and shuts down, i.e. does not rinse or wring. What to do?
The machine does only one washing operation and that’s it!
Turned on for 5 minutes and stopped
After switching on, it pours water, cranks the drum a couple of revolutions and stops. A click of the relay is heard.
Gets water, makes 2 turns and all.
Good day.
The same thing is happening to me, does anyone know a solution?
Tell me pliz!
Same problem. Corrected?
Has anyone solved this problem? It turns on, pours water, scrolls the drum with a stop three times and gets up. Then after a while again the same song. And for so long. Until the engine error pops up. I checked everything except the block, everything works. Probably the problem is in the block ...
And my car to me - with - tala (((
Already hands fall from a hand wash. I put it in the wash, after 15 minutes it stops and the display shows F-10. At the same time rinses through once and wring out!
When they bought it, they discouraged taking Russian equipment.
Indesit is not an option.
Drain does not work, what can I do?
Turn on the machine, the water flows by gravity. The water shutoff valve does not work. What can be done and what is the reason?
Did you find the reason? I have the same trouble!
Some operations work fine, and some constantly drain water. What could it be?
Have you forgotten to specify which valve is for supplying or draining water?
There is no valve to drain. The water level sensor may not work (under the cover on the right). Perhaps the tube is loose or has slipped from the tank to the sensor.
If water is poured with the machine turned off, then no options. Change valve.
The car is turned on, but in the drum, water appeared from somewhere. What is the problem?
The machine launches and turns off, that is, it does not rinse and does not squeeze, before turning off the water, it pumps out water, can anyone come across a similar one?
The machine after washing and rinsing does not include the spin mode. What to do? There are no funds for repairs.
Did you solve the problem? I have the same
My WISXE10 was turned on without water, then water was supplied. Now it can wash for several hours in a row, turning off periodically, after three minutes, ten, etc ... only the spin of 10 minutes works fine. What can be changed in it?
I have an Indesit IWSB 5085 machine, the lock hatch light flashes and does not start. What to do?
I have an Indesit machine, the lock hatch light flashes and does not start. What to do?
I ask for an answer for Boris
Replace lock
It is necessary to change the hatch lock and the triac Z0607 on the control board.
The machine erases, but does not rinse or wring. Help, what to do, what's the problem?
Indesit ewsd51031 - problems at the beginning of washing. First, the pump starts to drain, and then normal washing begins. There are no errors on the display, the drain hose is at a height of 100 cm. What could be the reason for this?
1. Check, clean the drain filter, drain hose.
2. Check the level sensor.
All indicators blink when rinsing and water leaves - what is it?
I turn on the machine, the door lock is on, I select any program, the lock goes out, but the door is locked.But the washing, spinning, rinsing and draining phase does not occur! What to do?
The same thing, I don’t know what to do.
I turn on the car, it erases, but after the first rinse, the rinse indicator and lock turn on, what is it? And, is it possible to set the washing mode to 50 degrees on the right key “5”?
The machine draws water, but does not start. And rinsing starts to work until the final cycle.
All the lights flash on the typewriter and it does not react to anything! What to do?
So I have the same parsley !!! If corrected, then tell me why.
What is the reason?
I plug into the outlet, it knocks out the light. What's the matter?
When spinning, it is so noisy, probably the bearings are broken? Where can I buy them?
All the lights flashed, smoke came from the drum. tell me what is it?
When drying, the indesit machine is very drumming, it feels as if something inside has flown off.
Same. I don’t understand, but the tank is not separable. Do not look.
The car door does not close, what to do
It starts to wash, then it stops, the red light blinks, the machine does not respond to anything, turn it off, then turn it on again, but in this mode the machine no longer works. Separately rinse, separately looking for some spin. Programs 4, 6, 7, 8 and 9 took off. What kind of garbage? who says repair or garbage?
The machine starts up, draws water, after the water intake, clicks are heard and nothing else happens.
Check motor brushes.
The fabric softener does not pour out from the dispenser. There is water in the dispenser.
The timer and the lock lamp often flash, what should I do?
The machine was washing well, but now it has stopped, it is gaining water, and it’s as if there aren’t enough forces to spin the drum. What to do?
The machine draws water, but the drum does not turn, the belt is in place, the brushes are normal. There is a suspicion - there is little water when draining in the system. I looked at the filter from below. Clean from above, where you put the powder - dry, water does not flow. Tell me, who had such a problem, the Indesit WISL 104 machine?
Clogged water inlet to the washing powder. Due to overdose of detergent.
The machine erases, the programs work, while spinning, water starts to leak through the door, what should I do?
Washed normally. But now he is gathering water, the drum is barely spinning and is very buzzing. What to do, can someone tell me?
Gets water and everything, dies and no movements.
After 19 years of excellent service, the Indesit WGS636TX washing machine stopped responding to the temperature setting. Water begins to boil regardless of the position of the switch. Most likely the thermostat is to blame. Who knows, are there any spare parts for such cars now and in general, is the game worth the candle and its repair?
Indesit WI101 - the washing mode switch does not work, runs in a circle, what should I do?
Has anyone answered anything, same problem?
When water is connected to the machine, the machine immediately begins to fill with water until you turn off the water. Something with an intake valve?
The machine washed, switched to rinsing and rinsing, without stopping for 3 hours, does not go to drain.
After rinsing, a beep sounds and returns to washing, while the wash indicator flashes and beeps. What could it be?
Indesit (vertical), comes to rinse and continues so, does not wring. It is necessary to stop and manually drain the water.
After washing in the switched off machine, water began to accumulate in the drum. If you merge, it is still typed. What to do? Every time I do not want to disconnect from the water supply.
When spinning, it makes a very loud noise! Tell me what to do?
Loud noise is the first suspicion of a bearing.
Turned on, started, and then completely went out and does not turn on!
Indesit IWSB5085 machine, select the mode, turn it on, the first portion of water is poured, click, all indicators begin to flash and the water is draining. There is no drum rotation. The brushes are normal. Hoses too ... tell me the reason.
Gathers water and immediately drains. And that’s all. Silence.
Indesit W105 TX stopped rinsing, some smell went, the lock does not open. What happened, what kind of malfunction?
Changed the heater, launched. 10 min. worked and everything went out. Enable does not exit. I look below small smudges. Where could water get and what to change?
I also can’t understand why she is either pushing it or not. It does not gain momentum and then the pump is very buzzing. Then all the lights blink, and the pump is very buzzing. I rolled two bolts on a saprostat. They were filled with red paint there, can they be adjusted or should a new one be bought?
When you turn on for a few seconds, all the lights on the display flash, then it works fine. What is it?
Most likely this should be the case when applying power.
Good day. You plug the machine into a power outlet, the bypass valve constantly clicks and water is drawn. If you disconnect the first connector on the valve, nothing happens. Then you turn on the first, and turn off the second, the valve clicks again and water is drawn. What could be the cause of the breakdown?
The washing machine turns on, but after a while the door lock key flashes in red. The program is running, but the machine does nothing (does not pick up water, does not spin the drum, etc.). But the door does not lock and cannot calmly open. Tell me what could be the problem? What is malfunctioning?
The red light is on, the door does not open.
W87TX worked in good faith for more than 10 years, but suddenly it turned on when turning on repeatedly to turn the program switch without stopping. None of the modes are turned on. What could be, someone came across this?
I just had the same. I changed the door lock and triac (I took out not my own, but an analogue. I worked for half a year). After reset the settings (5 seconds per switch). Now the problem is different, the machine turned on once. I turn on, the hatch lock is dimly lit, but it does not block it. I poke on the button on 5-10 times. And everything is working fine. But when I removed the control board, I noticed that it was 25% oxidized. Now I'm struggling with the inclusion of the washer.
The machine Indesit 51051g own house, water is supplied from the tank and is poured into the washing machine by gravity. The water supply valve does not turn off, I do not understand why. There is no pressure. Even when washing, water pours into the washing tub. New, first time included.
Most likely they connected incorrectly. Read the article “Why does the washing machine drain«
Indesit machine with the top opening of the lid, after the start of washing, the tank opened inside, it rumbled strongly and jammed. He doesn’t turn anywhere, the laundry is left inside, water has flowed from below to the floor. What to do? To repair, call the master or buy a new machine? The typewriter is 11 years old.
A bone from a bra fell from a drum into the inside. How to get her out of there? The wash is now dancing.
Try to drag it to the edge with a magnet, it will be difficult, but we did it!
WIA80. The water solenoid valve does not open. Coil 3.4 lbs.
What voltage comes to her when opening? Thanks in advance.
The vertical loading Indesit machine constantly draws water, what to do, tell me?
Help please!
It is not clear what is with the vertical. I turn it on, draws water, makes several revolutions, after which none of the indicators blinks. The switch starts to spin in a circle without stopping and buzzes quietly, as if draining water, and it is spinning.
Feed valve clogged.
Indesit iwse5105. It does not squeeze or drain water. That is, it shakes in one pore (erases) and at the end of f01 gives an error. The module was watched by specialists (related), they said normal, the engine is working, the tacho normal checked, what could be? Please tell me, I broke my whole head!
Washing as usual, rinses and switches to spin mode. And that’s all. Glitch. Alarm lamp and lock flashing. At the same time, the machine buzzes, as when draining the water. Does not respond to any buttons. I have to unplug from the outlet. This has not happened before. What is it?
Hello. Have you solved your problem with the machine? If so, please tell me what it was? I now faced the same problem.
indesit iwub4105 (CIS). Please, help! The ON / OFF button does not light up, the START / PAUSE button lights up and, it buzzes. Water is not poured. At the last wash, everything was fine. Thank you in advance!
Such a problem: it started to wedge, and some plastic flies from the filter. What could be, already the belt tore?
I turn on the mode, it starts normally and erases non-stop. The wash lamp flashes. You have to completely turn everything off and turn on the rinse mode, and then spin.
The machine does not start for a long time. There are no indications and sounds that came to life. After a while, F12 appears. How can I help her?
The spot indicator and lock blink. Error Code F04 VJUE Z PLTKFNM CDJBVB HERFVB.
And for me, when the machine without clothes all programs work. With linen - only spin, and washing does not work. Masters do not know what is the reason. Why the drum with linen does not twist and it is for washing. Maybe someone had it, tell me.
Washing machine Indesit WIL83. Set the mode. Launched the wash. After some time, the type machine pumps water and the lock buttons start to flash: rinse, iron (a button with an iron). And does nothing else. What could be? Thanks for the answer.
Indesit WISE127X. When you turn on the program, the lock closes, water is typed for 5 minutes, then the H2O display turns on without blinking. Water is poured on. Then the H2O display starts flashing, the water does not pour and there is silence. The lock is closed. What is the reason hiding and what kind of breakdown is it?
Constantly picking up water, gives an error 20.
Indesit IWSD 7105. All light bulbs flash on the typewriter and it does not react to anything! What to do? Throws error F12.
Does not pick up water, the relay is in perfect order. What could be? Indesit wgs 634.
I can not pull the rubber shutter on the neck of the drum.
Indesit iwsc5105. I cleaned the drain filter, now when starting it does not pick up water, all the lights blink.
Indesit wn421wu. It fills with water, starts washing, flows from below. What could be the reason?
Tell me, the machine does not start. The red light does not light up.
Please tell me, what about the machine, if it draws water and then immediately releases it? All indicators start to burn, the hose, as it should be at a level of 70-80 cm from the floor.
I have the same. Typewriter Indesit 5085.
The machine erases, everything is fine. But all programs are increased in time, i.e. I put it for 1 hour, we erase 2 hours, it adds time. At any time, you can stop the washing machine and it will open the door even full of water. What?
I bought a car Indesit EWSC S1051. After washing, the laundry is very hot. Who knows what is the reason?
I have a new machine leaking from the powder tray.At first it was dripping, and now it flows more when it draws water.
In the rinse mode, it began to drain not through the hose, but from above, through the powder tray. In other modes, it drains through a hose. Where to dig?
The indicator turns on, but the machine is in normal mode. Please tell me what is the problem?
Good evening. The drain does not start. Only spin is working. On the washing modes, 1-2 turns work, then it shows errors.
When you turn on the wash, water begins to accumulate without stopping and the drum does not spin. What is the reason?
Thank you in advance.
Everyone ...: with such knowledge it is better to cook grandmothers and call the master ... but "we are going to you."
The machine erases when the rinse mode is activated, water begins to spill out of the container, where the powder is poured.
Indesit iwsc5105. When you start the wash, it immediately abruptly picks up speed about 2-3 times and then dies, after a minute all the upper indicators light up and blink! The brushes are not worn out! I cleaned the anchor from soot but nothing has changed! Please help with advice?
I’m not a master, if that 🙂 As an option, maybe the control module flew ...
The machine erases, but only if you throw in some kind of easy thing. And if you load a few pounds, it does not pull. Designed for 6 kg.
It turns on, water is collected, it does not heat, it makes one revolution and that's it.
Indesit. The machine is 10 years old, has never failed, it worked perfectly. Now the problem: I chose the mode, the lamp of the first stage of the program lit up, the lock is closed - and that’s it. There is no water intake, no signs of work, just silence, maybe someone knows this problem, tell me?
Please tell me what is the reason? When starting, the controller constantly goes in a circle.
Hello, my machine worked well for 2 years, but for 2 days now it started to make a lot of noise with a squeal, it's scary! Tell me what you need to do?
Most likely the bearing failed. If you are lucky and the tank is collapsible, you can replace the part. And if, like everyone else’s, it’s not separable, then either completely change the tank (which is expensive) or find a craftsman who will cut the tank and do everything bypassing the services (they don’t do such repairs). And if your hands grow from the right place, then you can do it yourself. Here is the instruction: https://washerhouse.com/en/razobrat-nerazborniy-bak-stiralki/
The machine does not pump water, what is the reason?