All about washing machines

Door Error in Atlant Washing Machine

Door Error in Atlant Washing MachineWhen the door error message appears in the Atlant washing machine, most likely the hatch door is not completely fixed. The electronic control unit notifies you of the trouble through a special monitor. Hybrid models without a display recognize inaccuracies by the appearance of light in the area of ​​1, 3, 4 indicators. Let’s try to figure out what the problem is, and try to figure out how to fix it yourself.

Initial action

It became clear what the Door-error in the washing machine was talking about. The hatch door is not tightly fixed due to damage to the electronic unit or mechanics. We act in stages:

  • we check how the hatch is fixed;
  • tightly press the hatch;
  • evaluate the state of the closing device;
  • specify the state of hatch fixation;
  • we check the condition of the wiring;
  • evaluate the completeness of the functioning of the control mechanism.

Before making repairs, we try several times to restart the Atlant washing machine. You can decide what to do right, first several times, unplugging the device from the outlet for 20 minutes, and then turning it on. If the inscription disappeared, then the problem was a system failure, and if nothing has changed, you should continue to look for a way out.

Fix the locking mechanism

UBL broke on AtlantThe washing machine is equipped not only with a classic lock, but also with a more reliable door lock with electric filling. The UBL lock is responsible for the process of fixing the door, which may need to be fixed.

Masters argue that the reason lies precisely in the UBL, if the hatch is tightly closed, and the process does not start. The washing unit will not start the wash until the hatch is fixed according to all the rules, often the display shows the indicated code.

The blocking element operates from electrical impulses, under the influence of which the plates begin to gradually increase by pressing the lever. It may happen that the plates fail, and the lock has to be changed. To start, it is recommended:

  • check the locking mechanism with a multimeter;
  • check for blockages in the hole.

Often the reason lies in the clogged garbage, which does not allow the lock to be locked. Cleaning is possible only after analysis UBL mechanism. If the problem with the error on the display is not resolved, it is worth inspecting the wires located between the locking lock and the control module. Often with a detailed examination, you can find minor flaws that need to be fixed by isolation. At the end, we examine the module, measuring the resistance on the board with a multimeter. If a breakdown is detected, it will have to be repaired or a new one purchased.

Door mechanics

hinges on the door CMWe have indicated far from the whole list of reasons that can cause an unfortunate mistake. Be sure to check the health of a variety of elements, including:

  • the location of the hinges is on the side, since the door may warp during unprofessional installation or during prolonged use, so the latch does not fall into the lock hole. You can quickly solve the problem by tightening the hinges or by installing the hatch in the desired position;

It is mandatory to check whether the smooth working surface under the Atlant washer is ideally.

  • a handle that may break, so after completely removing the hatch door, it will have to be replaced with a new one;
  • tab in the form of a tongue, which has the property to move and release the holding pin. The malfunction can be eliminated by completely disassembling the lock mechanism.

Guides made of plastic can also wear out significantly. If when using the washing machine for its intended purpose there is no characteristic click of the hatch closing, then the guide should be checked and replaced.

Replacing the door locking mechanism

If it became clear to you that the unit knocks out the Door error due to failures in the mechanics, then the handle or its individual parts must be replaced. To fix the problem, it is necessary to carefully dismantle the door from the SMA, removing a couple of mounting bolts. After that, the hatch is laid on a smooth table, the bolts securing a pair of door parts are unscrewed.

If you want to return to the initial position of the latch-tab, you should raise or lower the fixing pin. If you completely disassemble the element, then you can put the purchased pen:

  • remove the spring;
  • put the locking element;
  • carefully screw in the pin;
  • lock the handle up.

Now it became quite clear what to do when the washing machine shows the Door code on the monitor. The owner can cope with the damage on his own if you try to repair the mechanism according to the above instructions. Good afternoon!

   

Reader Comments

  • Share your opinion - leave a comment

Add a comment

Read also

Error codes for washing machines