Failures of the Whirlpool washing machines

Cars from the middle price category under the Whirlpool brand, like any other, are not insured against breakdowns. They also fall into the service centers to the masters, who have already compiled a list of the most common malfunctions of these units. For the most part, they do not differ from breakdowns of washers of other brands, but there are still features in the repair, but first things first.

Frequent breakdowns

Most Virpul washing machines are equipped with a good self-diagnosis system, as a result of which the machine displays error code. This greatly facilitates troubleshooting, so if a code appears on the machine’s display, be sure to read the instructions. But what if the washing machine does not turn on at all? Here the self-diagnosis system will not help. Masters note that most often in Virpul washing machines break:

• a heating element;
• engine or its movable elements;
• drum cuff and nozzles;
• control board.

Important! In Whirlpool typewriters, clogging of filters and hoses often occurs, but all this is easily solved independently if you clean them in a timely manner.

Breakdown ten

If the machine does not start washing or does not turn on, then one of the reasons may be a breakdown of the heater. Sometimes the machine turns on, it can work, but it can be washed in cold water. In this case, it is necessary to check the heating element and replace it if necessary. This is done as follows:

• the back cover of the case is removed;
• the power wires and the sensor are disconnected from the heater;
• the nut on the screw is loosened, which is located in the center of the heater base;
• the screw is pressed into the PETN, which then must be pulled out on itself with shaky movements;

Note! If the heating element sits very tight and does not give in to movement, try spraying it with WD-40 liquid, wait a little and pry the heating element with a flat screwdriver, pull it towards you.

• through the hole under the heater we clear the tank of debris and dirt;
• insert the heating element into the nest and tighten the nut, trying not to twist it, otherwise this will lead to the ten being squeezed out into the tank during washing;
• connect the wires and temperature sensor;
• collect the machine.

Engine malfunctions

Quite often, Virpul washing machines fail. Moreover, breakdowns are mostly simple, they can be completely eliminated with your own hands. Most often, the brush motors of Virpul washing machines wear out brushes.

For this reason, the engine first loses power, and then completely stops spinning the drum at an acceptable speed under load. In this case, the washing machine turns on, and the washing program starts. How to troubleshoot a Whirlpool brand washing machine engine? To get started, get to the engine.

1. We disconnect the washing machine from communications and drag it to a place convenient for repair.
2. We unfold the machine with the back wall towards us, take the star screwdriver and unscrew the screws holding the back wall, disconnect the plastic latches.
3. Having removed the back wall of the Whirlpool washing machine, we find the motor, which is located directly under the tank.

The engine is found, now we need to make sure that the brushes are really worn out in it. You can unscrew the engine, disconnect the wires, pull it out of the housing, pull out and inspect the brushes. You will spend 15-20 minutes on everything about everything. And you can determine the wear of the brushes in a couple of minutes. How to do it?

We take a hammer and apply a few light blows to the engine body. With all your strength you do not need to hammer, but the blows should be palpable. We turn on the washing machine in the network and run the test program. If the engine began to work in normal mode, then the brushes must be changed unambiguously. If the engine still does not work, then the problem is not with the brushes.

If the Whirlpool washing machine does not turn on, then there are 2 malfunctions, or the control module was initially malfunctioned.

Turn off the Whirlpool machine again, remove the drive belt, unscrew the bolts holding the engine. We take out the engine, unscrew the screws holding the brushes with a Phillips screwdriver. We pull out the old brushes, make sure that they are worn out and replace them with new ones. We put the engine in place, put on the drive belt, install the back wall, connect the Whirlpool machine and check its operation. If the machine does not turn on, check if you have connected all the wires to the engine and its sensor.

Cuff wear, housing corrosion

Any washing machine of the Whirlpool family has a rather unpleasant “sore”, which, although it does not affect the performance of the equipment, greatly spoils its appearance. The fact is that the quality of the metal from which the Whirlpool machine body is partially made leaves much to be desired, it is susceptible to corrosion. In general, this problem does not bypass the majority of modern automatic washing machines, but for some reason the corpus of Virpulov is faster.

In this case, the problem can only be solved radically - by replacing the parts of the case. It’s pointless to clean and tint the case with paint, the appearance of the machine will not be restored from this. In addition to housing corrosion at the washers Whirlpool has another weak point - the cuff and the rubber bands, especially the cuff. What is the weakness?

The fact is that the material from which the cuff of the Whirlpool washing machine is made deteriorates under the influence of moisture. If the cuff is not wiped off from moisture after each wash, after 1.5-2 years of use, it will crack and begin to leak water. Check the cuff.

The cuffs of such washing machines as Samsung LG Miele Ariston are not so sensitive, but they can become unusable if they are wet all the time.

• Open the hatch of the washing machine.
• Carefully feel and inspect the cuff for cracks and gaps. At the same time, try not to mistake the cuffs for convexity and concavity provided for by the design.
• If damage is found, remove the old cuff and install a new one.

Read how to replace a damaged cuff of a washing machine. The cuff in the washing machine is torn - what to do?

Management board

If the Whirlpool washing machine does not turn on, it is likely that there are problems with the control board. In this case, diagnosing the problem yourself is quite difficult, it is better to contact the master. In fairness, it should be noted that if the machine Whirlpool does not turn on, a problem may occur in the electrical circuit, in the FPS or in the supply wire.

A qualified specialist will determine exactly what the problem is, determine which components are required, and how much the repair will cost. Then you will decide whether to repair the washing machine or whether it is better to buy a new one.

Summing up, we note that every day in the world about a dozen washing machines of the Whirlpool brand break down. As a rule, engines, pumps, heating elements fail, but problems with the sunroof cuff and control board may occur. If the machine does not turn on or there is another incomprehensible "symptom", it is better to consult a specialist. Have a good repair!