Error codes for washing machines Whirlpool

• Make sure the tap water supply is not shut off. That is, the tap is in the open position.
• Make sure that the inlet hose is not pinched or clogged. Inspect the strainer strainer. It is located at the junction of the hose and the machine.
• Make sure that the filler valve is working.

If there is water in the tank of the machine:

• Make sure that the pressure switch tube is not clogged and is firmly connected to the level switch and to the drum of the washing machine.
• Make sure that the drain pump is not broken.
• Make sure that the pressure switch is working.
• Ensure that the electronics module is not malfunctioning.
• Make sure that the pressure switch (level sensor) is functioning properly.
• Inspect the siphon for obstruction.
• Inspect hoses; water may leak.

• Make sure that the drain pump is not broken and is working properly.
• Inspect the wiring and contacts.
• Inspect and clean (if necessary) the drain pump filter. Its blockage can interfere with the discharge of water.
• Make sure that the drain hose is not pinched, kinked or clogged.
• If you did everything, but when the wash starts, this error occurs again, then you should replace the pump.

• Make sure that the sensor is firmly connected to the heater and relay.
• Make sure that the sensor is working.
• Make sure that the heating element, its wiring and relay are working properly.

• Make sure that the electric motor of the washing machine is working.
• Make sure that there is no open circuit between the engine and its control panel.
• Make sure that there is no open circuit between the engine control panel and the electronics module.
• Make sure that the control panel of the electric motor is working.
• Verify the integrity of the wiring.

• Make sure that the control panel of the electric motor is working properly.
• Make sure that the motor is in good condition.
• Make sure that there is no violation of the integrity of the wiring.
• Make sure that the contacts between the engine and its control panel are working.
• Make sure that the contacts between the motor control panel and the main control panel are working.

• Verify that the wiring and contacts of the drain pump, control panel, and pressure switch are working properly.
• Make sure that the drain pump filter is not clogged.
• Check drain hose. It must not be pinched or clogged.
• Make sure that the drain pump is working.
• Check the pressure switch (level switch).
• Ensure that the inlet valve is working properly.

• Check engine.
• Make sure the engine control panel is working properly.
• Check the location of the washing machine. It should not be near the battery. It is also desirable to have ventilation in the room.
• Make sure that the contacts and wiring are working.
• Make sure that moving parts are not worthless.

• Make sure that the moving parts are not worn out and are working properly.
• Check wiring and contacts.
• Make sure that the electric motor is working.
• Check the engine control panel.
• Make sure that the central control panel does not break.

• Check the metering motor.
• Inspect the dispenser and its motor for mechanical damage.
• Make sure the contacts and wiring are working.

• Verify that the main control panel is working.
• If the reason for the occurrence was the voltage drops, then perhaps turning off the machine for a couple of minutes and then turning it on will help.

• Ensure the integrity of the wiring and other connections.
• Check the electric motor of the washing machine.
• Make sure the drive belt is in place and not worn.
• Check motor control panel.

• Make sure that the drain pump and pressure switch are working properly.
• Check the drain hose for kinks or clogging.
• Verify that the main control panel is working.
• Make sure there is no clogging in the drain pump filter.
• Check the wiring and tightness of the contacts.

• Faulty lock or its absence.
• Ensure the integrity of the contacts and wiring of the drain pump, the main control panel and the persostat.
• Possible damage UBL (locking device hatch washing machine) or its wiring.

• Check the wiring from the control panel to the UBL.
• Possible failure of the castle.
• Also make sure that there are no foreign bodies in the lock mechanism and UBL.
• Make sure that the UBL (hatch blocking device) is working.