All about washing machines

Haier washing machine error codes

first pictureHaier washing machine error codes are nothing more than a means of communicating their self-diagnosis systems with the user. If a malfunction suddenly arises in the washer, this system will display a special code on the display, decrypting which the user will be able to roughly understand what is broken and take action. It turns out that we need, first of all, to understand how the error codes of the Hyer washers are decrypted, and we will do this within the framework of this publication.

User Issues

In some cases, the user himself becomes the reason that the Haer washing machine stops washing and displays some kind of error. Anything can happen, the user forgot to put powder in the tray and launches the laundry without powder, overloaded the drum with laundry or did not distribute the laundry in the drum correctly, well, let's not make a "semantic confusion", we list these errors and briefly describe them.

  1. No salt. This inscription, which is also an error code, eloquently notifies the user that there is no powder in the tray. If you poor quality powder in the trayWe are sure that they poured the powder, which means that, most likely, the powder receiver channel is clogged. In rarer cases, a washing machine Haier mistake No salt reacts to low-quality powder.
  2. UNB. This code informs the user about the imbalance inside the drum. As a rule, an imbalance occurs due to the fact that the user did not correctly distribute the laundry in the drum, laying it before washing. Sometimes an imbalance arises due to the fact that the user erases one voluminous and heavy thing.

Often, an imbalance can occur due to insufficient or vice versa excessive loading of the drum of a Haier washing machine. Try to load the drum correctly.

  1. ERR1 This error occurs when the machine cannot start the wash due to an unopened hatch. The main reason is that the user simply loosely pressed down the hatch, and the hatch did not close accordingly, and an error popped up. But often this error is caused by a breakdown of the hatch lock device or a broken latch on the hatch door.

Problems with filling and draining water

Failures associated with the inability to fill the machine’s tank with water or vice versa to drain the water are quite common, it can even be said without exaggeration that they are the most common. That is why in the self-diagnosis system of the Haier washing machine, so many codes are devoted to water-related malfunctions, let's list them.

  • ERR2 The appearance of this code is due to the inability to drain the water from the tank for 4 minutes set by the program. There are several reasons for this: the pump is clogged or broken, the drain hose is bent incorrectly, or the drain hose is twisted or broken.

In some cases, ERR2 pops up when there is a power failure in the drain pump of the Haier washing machine.

Hyer washing machine pump broken

  • ERR5 Indicates that it is not possible to pump water into the Haier washing tank. The washing machine must pump water to the level set by the program for a maximum of 8 minutes, if this does not happen, this error appears. Why is this happening? There are several options: the water pressure is very low, the tap is closed and therefore the water supply is impossible, the net of the filling valve clogged with debris, the power supply to the filling valve, pump or pressure switch is disturbed.
  • ERR8 This code tells you that too much water has accumulated in the machine’s tank. In such a situation, in 97% of cases, the faulty pressure switch becomes the culprit of the error. In much more rare cases, this code generates a burned-out triac of the control board, which controls the water level sensor.
  • ERR9 As strange as it may seem, this code is decrypted in the same way as ERR8, with the only difference being that ERR9 give rise to other reasons. In particular: the filling valve burned down, so the module cannot stop the water supply to the tank, the triac controlling the filling valve burned down.
  • ERR10 This error is also associated with a malfunction of the washing system hydraulic system, but unlike the codes described above, in our case, the filling valve functions normally, but the pressure switch is broken in 99% of cases.

clogged intake valve

Problems with heating water

Now let's talk about the errors associated with heating water in a Haier washing machine. Let's list these codes and then decrypt them.

ERR3. Literally, this error code can be deciphered as: "... the heating element is not able to heat water to the temperature set by the program ...". Also, this error appears if ten does not heat water at all. The main reasons: the temperature sensor has burned out or the power of the temperature sensor is broken.

ERR4. This code is decrypted in exactly the same way as the ERR3 code, although the reason for the appearance of ERR4 is not a burnt thermal sensor, but a burnt ten. In addition, if the power of the heating element is broken and it does not turn on, an ERR4 error pops up.

Electrics and Electronics

The Haier modern automatic washing machine is crammed with electrics and electronics. A large number of wiring, tied into bundles, is designed to power dozens of sensors and modules that ensure the functioning of the machine. Well, the electronic module controls this entire complex system, ensuring its operability. If any of this fails, the self-diagnosis system of the washer will warn the user by issuing one of the following codes.

ERR6. This error tells us about the malfunction that occurred on the control module board. There can be many reasons. One of the tracks may be damaged, one or more semiconductor elements may fail, or contact between the track and such an element may be lost.

In a few rarer cases, this error pops up if one or more wires in the block of the control module board that fits to the connector of the board sits loose, which makes the contact disappear.

burner module burner Hayer

ERR7. This code can be seen not so often. He tells us that several parts of the control module burned down at once and this malfunction is critical. This can happen, for example, as a result of a short circuit. ERR7 is a more serious problem than ERR6.

EUAR. This is another serious malfunction that occurs, as a rule, in the control module. In more rare cases, this error pops up when a whole bundle of wires that are suitable for the electronic module is burned out.

Troubleshooting

Now it's time to talk about fixing the causes of the above errors. Of course, we will talk briefly, without details, since there are special thematic articles for a detailed description of eliminating all malfunctions.

If the inscription No salt popped up, you need to check if there is powder in the tray or not, either clean the powder receptacle channel, or change the powder to a better one. Is there a UNB code? Stop the washing and distribute the laundry inside the drum of the Haier washing machine and restart the washing. If you encounter an ERR1 error, try pushing the hatch with your knee without turning off the washers. Often this measure helps to start the wash. If this does not help, you have to repair the hatch lock of the washing machine.

If the ERR2 code appears, check the drain hose. Perhaps it is bent incorrectly during installation or clogged, so the water does not leave. If everything is normal with the hose, you will have to climb into the housing, remove the drain pump and clean it of dirt. At the same time, you will need to check it with a multimeter for malfunctions and if any, replace the part. If you encounter an ERR3 error, feel free to remove the back wall of the Haier washing machine and check with a multimeter the temperature sensor and the wiring that suits it. Most likely, the sensor will have to be changed.

check tener washing machine Hayer

ERR4, it will force you to check not the temperature sensor, which, by the way, is installed on the heating element, but the heater itself or the wiring. The one that fits him. First of all, you need to measure the ten's resistance, then take on the electrician supplying it. If an ERR5 error occurs, you need to check if there is water in the water supply and if all the taps are open.If water is supplied, but does not get into the washing machine, you need to remove and wash the filter mesh, which is on the inlet valve. Well, if this does not help, you will have to alternately check the filling valve, pressure switch and pump with a multimeter.

Faced with the ERR6 error, you can restart the Hyer Washroom by unplugging it from the network and turning it on after a couple of minutes. If such a measure did not help, feel free to call the wizard, since you are unlikely to fix the control board yourself. By the way, the ERR7 code should prompt you to the same actions as in the case of the ERR6 code, however, in this situation, you need to be mentally prepared for serious costs.

The ERR8 code lets us know that it is time to check the pressure switch of the washing machine. Start with his tube. It must be purged and carefully cleaned of dirt, after which it is necessary to check with a multimeter. If you encounter an error ERR9, feel free to check the intake module with a multimeter. First, inspect the inlet valve itself, it may be clogged with dirt and cannot open and close normally, then check the electrician. If necessary, the inlet module must be replaced.

And finally, faced with the ERR10 error, open the top cover of the Hayer washer and carefully check the pressure switch and the electrics that feed it. First, check the resistance of this part with a multimeter, and then check the wiring of the power supply for a breakdown.

In conclusion, we note that the Haier washing machine, like any other modern automatic washing machine, has a self-diagnosis system that “communicates” with the user through a special code system. To "understand" the washing machine, you need to know the decryption codes for this system. Actually, we presented this decryption in this article, we hope this information will be useful. Good luck

   

25 reader comments

  1. Gravatar Vitaliy Vitaliy:

    Haier shows EUAR error, not a single workshop takes care of repairs. Everyone has one opinion, this brand of washing machine is disposable! Not subject to repair.
    How can this be?

    • Gravatar Dmitry Dmitriy:

      You just need to think with your head and turn to their service, and not run around private offices.

  2. Gravatar Zet Zet:

    Closed wires in the braid to the control module

  3. Gravatar Marina Marina:

    LOCH was displayed during washing. And not a single button works.

  4. Gravatar Kostya Kostya:

    Hello. On the washer, the sort mode blinks when on. Choose a program, it blinks. Turn on -
    stops blinking. What could it be?

    • Gravatar Oleg Oleg:

      The same nonsense. It does not seem to affect performance, but it is slightly annoying (

    • Gravatar Lily Lily:

      The same problem ... Did not find a solution?

  5. Gravatar Rum Rum:

    Highlighted a Loch error. And it stinks of it with singed wiring. Is this normal?

  6. Gravatar Denis Denis:

    Error # 10, the drum does not open. Washed without laundry, because the son poured a liter of rinse aid into it. What to do? Haier washing machine HW 60 1082s.

  7. Gravatar Marina Marina:

    ERR2 error, how to fix? When washing in any mode, the drain works for a long time, and then it starts to saw. Click on the start, it starts working again. This error is constantly appearing.

  8. Gravatar Elena Helena:

    Error E1 is on. The filter was cleared, but at startup the machine does not allow you to select a new program and launches an incomplete program. Then throws this error.

  9. Gravatar Sergey Sergei:

    During washing, the machine stopped and LOCH lights up.

  10. Gravatar Vera Vera:

    We have E1 on the display. There is no decryption in the instruction.

  11. Gravatar Anonymous Anonymous:

    E4 issues

  12. Gravatar Igor Igor:

    We have E4 on the display. There is no decryption in the instruction.

    • Gravatar Nastya Nastya:

      Tell me, how did you deal with the e4 error?

  13. Gravatar Anton Anton:

    ERR7 on the Haier HW60-B1286S. Heating element error. Our TEN burned out.

  14. Gravatar Aurora Aurora:

    Hello, when you turn on, end appears on the screen, then lost, then what does this mean? The machine does not work and the door is closed, does not open.

  15. Gravatar Irina Irina:

    Hello, tell me, the machine gives an error er16.

    • Gravatar Vasya Vasya:

      Smart people say that this is most likely a malfunction of the electronics module. It’s better not to dig yourself. Call the master. I think that the repair will cost a lot.

  16. Gravatar Vladimir Vladimir:

    SMA Haier hw50-12866me. There is no gulf of water between the zero of the 220V network and the neutral (mass) of the control board; the multimeter showed the 3rd (the door is open) and the 9th (the door is tightly closed ... it looks like a fault. Or ... what?

  17. Gravatar Catherine Catherine:

    And if the display shows fco - what does that mean?

  18. Gravatar Olga Olga:

    Hello. Error E1 is on the screen, what does this mean?

  19. Gravatar German Hermann:

    The fa4 error is on with a characteristic beep. What could it be?

  20. Gravatar Sergey Sergei:

    err 10 sometimes happens if you don’t close the door, then close it and don’t restart the wash program.

Add a comment

Read also

Error codes for washing machines