Error codes for Atlant washing machines
Most new home appliances have several important features.
In addition to their immediate functions, they also inform about what kind of failure prevents them from working normally!
Let's move on to describing error codes for washing machines.
Error Codes
Error signaling | Decryption | Fault Options | Repairs |
Typewriter with display "Sel". On a typewriter without display: indicators do not light | Interface module selector failure | Potentiometer that selects programs may break. | Change the interface module. |
On display: "None". If there is no display, all indicators light up. | Excessive foam formation. | Too much powder was used for washing. | Limit the amount of washing powder to smaller ones. |
Error mode set. That is, a regimen with an excessive amount of flooded water. | Select the washing mode that is designed for this type of fabric. | ||
Used detergent or other detergent not suitable for machine wash. | Use only those products and powders that are intended for machine washing. | ||
Display: "F2"The third diode is on. |
The temperature sensor is out of order | Problems with the wiring and contacts of the temperature sensor or module. | Make sure that the wires and contacts are working. |
The temperature sensor has deteriorated. | Change the heating element (TEN). | ||
The control module is out of order. | Replace the failed module. | ||
Display: "F3"The 3rd and 4th indicators light up. |
The heating element of the washing machine (TEN) is out of order | Damage to the heating element. | Replacement of a heating element (TENA). |
Broken contacts or wiring. | Make sure the wires and contacts are working. | ||
The control module is out of order. | It is necessary to replace the module. | ||
On display: "F4"Glow 2nd diode |
Damage to the drain pump (pump) | The drain hose is clogged or pinched. | To straighten a hose, to find and eliminate a blockage. |
Incorrect hose installation. | Reinstall the hose as instructed. | ||
If a foreign object enters the pump, it locks up its impeller. | Remove the trapped object, check the rotation of the impeller. | ||
Damage to the drain pump. | Change a broken pump. | ||
Fuse ball in the drain sleeve. | Drain the water from the machine using the tube and change the coupling | ||
Clogged drain clutch. | Perform a cleaning. | ||
The problem with wiring and contacts. | Make sure that both are working. | ||
The electronics module is out of order. | Change electronics module. | ||
Display: "F5"2nd and 4th indicators are lit |
Damage to the filler valve | Water inlet hose filter clogged. | Filter cleaning. |
Clogged or pinched inlet hose. | Unscrew the hose from the machine. Let the water run for inspection. If necessary, clean the hose. | ||
There is no water in the water supply, the water supply in the tap is not open, or the filling valve is broken. | Make sure the tap is in the open position. Make sure that the water supply is not disconnected. Change valve if necessary. | ||
Open circuit between the control module and the inlet valve. | Use a tester to verify the presence or absence of a break. | ||
Jamming contact failure | Make sure that the contacts are operational. | ||
Control Module Failure. | Replace it with a new one. | ||
Display: "F6"2nd and 3rd indicator is on | Problems with the relay of the electric motor of the washing machine | Overheating of the stator winding. The contacts responsible for the thermal protection of the engine are disconnected. | Change the engine of the machine. |
Display: "F7"Lights: 2nd, 3rd and 4th indicators |
Electricity problems | Interference Filter Breakage | It must be changed. |
The voltage in the network does not match the necessary (more or less). | Carry out a network check with the tester. | ||
The control module broke. | Replace it. | ||
Display: "F8"LED number 1 is on | Too much water in the washing machine tank | Damage to the pressure switch. | Replace pressure switch. |
Jam valve stalled. | Replace the valve. | ||
Problems with wiring or contacts of the pressostat and control module. | Make sure that the wires and contacts are working. | ||
Violation of the tightness of the cylinder. | Carry out a cylinder check. | ||
The control module has broken. | Change it to working. | ||
Display:"F9 »Indicators No. 1 and No. 4 are lit | Problems with the engine tachometer | Broken contact or wiring of an electric motor or control module. | Verify the presence or absence of a problem by checking the wires and contacts. |
The engine or tachogenerator broke. | Change engine. | ||
Control Module Fails. | Change it to a working one. | ||
On display: "F10" If the machine is without a display: indicators No. 1 and No. 3 are illuminated |
UBL failure (blocking) | Fault in blocking. | Change it to a new one. |
Control Module Failure. | Replacement. | ||
Display message: "Door"Hallowed 1st, 3rd, 4th indicators | Possible breakdown of the lock (UBL) | No contact in blocking . | Make sure that the wires are connected correctly and that there are no breaks. |
The hatch is not tight enough. | Lock the hatch again. | ||
Skewed door or lock. | Straighten the hatch / lock. | ||
Open circuit between the control module and UBL. | Use a tester to test the circuit. | ||
Lock Connector Problem . | Verify proper wiring and wire integrity. | ||
The control module is out of order. | Change it. | ||
Display: "F12"1st and 2nd indicators are lit | Possible triat engine failure | The engine of the machine broke. | Replace. |
Open in motor winding. | Replace the engine. | ||
No contact. | Make sure the wires and connector are working. | ||
The control module has broken. | Change it. | ||
Display "F13"1st, 2nd, 4th indicators are lit | Various breakdowns | Problems with wiring or contacts. | Check the wires and contacts. |
The control module broke. | Change to a new one. | ||
On display: "F14"1st and 2nd indicators | Program crash | The program crashed. The electronics module is incorrectly programmed. | Replace the module. |
Display: "F15" | Water leaked | The tank was depressurized. | Replace it. |
Leaking through a closed door | Change the cuff of the hatch. | ||
Violation of the sealing of the drain hose, nozzles, drain sleeve | Try to locate the leak and fix it. Make sure that the clamps fix the pipes well enough. Ensure the integrity of the nozzles and drain hose. |
Interesting:
Add a comment Cancel reply
Headings
Washing machine repair
For buyers
For users
Dishwasher
The washing machine Atlant has been working for me for the 5th year. No complaints. If I change the machine, it’s only Atlant. My Atlant bought a refrigerator in 2010. There are no complaints either, it works perfectly. Keep it up guys. Well done. I myself am from Donetsk. Thank you for the good products.
in two years, the third failure — module !!!!
It all depends on karma, I also have an atlas machine, a freezer. Everything is working
7 months error 15 service helpless
5 years old typewriter - not a single failure. just a little noisy. Also a refrigerator. Well done!
Machine Atlant - 6 years everything was fine. At the next wash, it turned on and lights up - the end of the program and the lock. And it does not clean up and does not start. What to do? Help!
I worked for 4 years and that's it, the module flew. Replaced, then another soldered tank. In general, there is nothing more to repair. Better to buy a new one. I understand that now all the cars are no more than 5 years old and everything is new. Such a policy.
I do not know what to do.The machine gives an F8 error, it worked perfectly before the shutdown, took it as a spare since I need a large washing machine in constant washing. Now the main one has broken and this one gives out that there is a lot of water in the barrel, although this cannot be. She stood for 4 years.
Error f16, what is it?
Clipper Atlant knocks out error f13. Indicators 3,4,6 are on. What to do, what is the reason? Tell me?
Knocks out error n, what does this mean?
This is not a mistake, but a night wash mode.
No karma! For 1.5 years, the washing machine breaks down 4 times. Before that, I could do without a wizard, and now I can’t even find the error code R. Thank you, domestic producer!
Hope “n” is not a mistake, but the “night wash” option is turned on. There is a button on the panel - you can turn it on and off the option 🙂
f13 - change the control module, the firmware has flown.
f16 - heating did not turn off. Change either the control module or the heater. What exactly, do not remotely diagnose.