Electrolux Dishwasher Error Codes
Diagnosing a dishwasher in the event of a breakdown will be faster if you know the decoding of the fault codes. In the Electrolux brand dishwashers, the manufacturer has programmed such codes (i 20, i 30, etc.) not only in the model of machines with a display, but also without it.
If the machine does not have a display, then a specific error is reported by the blinking of the End indicator (end of the program), the main thing is to know what such blinks or symbols mean. We offer their decoding in this article.
Errors in dialing, draining and heating water
The most common, regardless of the brand of the dishwasher, are breakdowns and malfunctions associated with the filling and draining of water. And all because in most cases they arise due to improper connection to the water supply or sewage system, as well as in violation of the operating rules.
- The i10 code or one flashing of the indicator with a five-second delay indicates that there is no water in the dishwasher. If a certain amount of water is not poured into the tank of the machine within one minute, the cause may be a closed water supply tap, a bend in the water supply hose or a clogged filter in front of the inlet hose. Similar causes are resolved on their own, without any difficulties.
Important! Do not confuse the English letter I (“ay”) with the number 1 displayed on the display of the dishwasher.
- Code i20 or two flashes indicate that there is no drain in the dishwasher. If the machine fails to drain the waste water for a certain time and the i20 error appears, then the cleaning filter may be clogged, the drain pump is broken, the drain hose is pinched, and the water level sensor is faulty. Usually, to eliminate error i 20, it is enough to clean the filters that are clogged with food debris, seeds, sometimes pieces of broken-off dishes.
- Code i30 or three flashes of the End indicator light means that the water leak protection has tripped. To be more precise, water got into the pan, the float worked and in the Aquastop system a valve was opened that shut off the water supply. To eliminate this error, it is necessary to drain the water from the pan and change the Aquastop hose (if it is mechanical) or simply drain the water and remove the float from the “water” position by tilting the dishwasher for this.
- The i60 code or six flashes of the indicator means that the dishwasher does not heat water or warms it above the set temperature. In this case, the reasons may be as follows:
- burned up ten;
- electrical wiring failure;
- temperature sensor breakdown;
- a small amount of water collected;
- breakdown of the circulation pump or control board.
Most often, service center masters are faced with the first three problems.
You can replace a heating element or a temperature sensor at home, if there is even a small skill in working with equipment. It is much more difficult to diagnose a fault in the wiring and control board, so in most cases this work is trusted by the master.
- The code iF01 on machines without a display appears as 14 flashes of the indicator. This error is related to exceeding the permissible time of water filling, i.e. the water in the dishwasher was taking too long. Despite the appearance of this error, the machine continues to wash the dishes with a small amount of water until the water is drained, after which this error is eliminated.
Errors related to electrical and sensors
This group of errors can be called more complex both in terms of diagnosis and in terms of elimination. Here are the error codes for Electrolux dishwashers:
- The i50 code or five-time indicator blinking informs the user about the malfunction of the triac responsible for the operation of the circulation pump. With such a malfunction, the pump runs at full power for a while, after which the washing program stops altogether. The error can be eliminated only by replacing the triac on the control module.
- Code i70 or 7 flashes of the indicator - malfunction of the thermistor of the heating element, as a result of which washing is carried out without heating the water. Replacing the NTC thermistor will solve this problem.
- Code i80 or 8 flashes of the indicator - an error in the EEPROM memory of the control module. To solve the problem, you need to flash the module or replace it with a new one.
- An i90 code or 9 flashes of the indicator indicates a violation of the checksum of the MCF or CCF control board. In this situation, it is impossible to select any washing mode, only the on-off button is lit. The problem is solved by replacing the module.
- Code iA0 or 10 flashes of the indicator means that the rocker arms do not rotate. This may be caused by jamming due to a power surge. Most often, the reason is much simpler - improperly placed dishes interfere.
- The code iB0 or 11 flashes of the indicator indicates that the sensor determining the transparency of the water has broken, a breakdown occurs if there is no data on the turbidity of the water for 15 -20 seconds.
- The IC0 code or 12 flashes of the indicator appears if the connection between the control panel interface and the board is lost. Diagnostics of the board and its further replacement are necessary.
- The id0 code or 13 flashes of the indicator informs about the breakdown of the tachogenerator of the circulation pump in the absence of a signal for 20 seconds. In this case, the water does not heat up.
Faults and difficulties of elimination
Repair and troubleshooting of dishwashers Electrolux can belong to one of three categories of complexity. The simplest repair can be done at home and it does not take much time, enough for 20-30 minutes. This applies to checking the machine for blockages, kinks in the hoses, as well as replacing parts during partial disassembly of the machine body. Repair of medium complexity includes:
- pressostat replacement;
- pump replacement (error i 20);
- cleaning the inlet hose and filters of the water inlet system;
- replacing buttons on the control panel.
For complex repairs, you must completely disassemble the dishwasher or dismantle parts and assemblies.
Such repairs, for example, include replacing a circulation pump, a transparency sensor, a heating element, and a control module. If you are interested in how to implement dishwasher repair Electrolux, then a detailed article has been written about this.
In conclusion, we note that the correct diagnosis of the error code of the dishwasher will reduce the time to troubleshoot. Manufacturers give the decoding of the codes in the instructions for the equipment, but if the instructions are not at hand, go to the site and read our articles. We hope the information was useful to you.
Interesting:
21 reader comments
Add a comment
Headings
Washing machine repair
For buyers
For users
Dishwasher
Thanks for the help, everything is fine now.
The machine knocks error code 60, what does it mean.
Tell me, 32 was displayed, what does this mean?
The UNT industrial dishwasher generates a CA ii error. What it is?
What does it mean if a machine writes CLO LO5 OSE?
ELF 43020, got a lot of water and drained. After that, the “Cancel” and “End” LEDs blink constantly (the first is faster). What could be?
Why blinks 4 times? There is no such error code! Buzzing and 4 blinks, tell me what does this mean?
Please tell me what it means 4 short flashes in a row at the dishwasher Electrolux ESF9421LOW? The machine only turns on, the indicator immediately starts flashing, 4 times intermittently and (in my opinion) the pump is buzzing. With what it can be connected? Before that, I took apart the car, there was an i30 error, assembled, this crap started! Nowhere is there an i40 error code, tell me who knows.
I have 4 blinks. ESL 65070. No site has this error.When you turn on - the hum below and immediately begins to flash, without turning off. And we did not make out. The same trouble, it seems. If you find out - write, pliz.
Have you figured out a 4 blink error? How to fix it?
i40 - faulty pressure switch. After replacement, everything works.
Thank!
Tell me, the display lights up 13 and that's it, the dishwasher Electrolux ESL 48010. Does not work.
Hello! In the PML ESL 6601ROK code i50 - "You can fix the error only by replacing the triac on the control module." Is this enough or can it be a consequence of including another malfunction?
The triac replaced, the motor checked, does not wedge, but the error still appears.
What could be another matter, tell me?
The triac replaced, the motor checked, does not wedge, but the error still appears.
Tell me, what else can I do?
This jammed the water level sensor, which is located on the pallet of the machine. The easiest repair is to remove the clamp from the sensor (this is a foam bucket). Good luck to all!
Tell me what to do? I choose the program. I close the car. She does not turn on. I open the door. The display shows 107 and all. Electrolux ESL 47030. Doesn't work.
i40 - faulty pressure switch. After replacement, everything works.
Tell me, what about the machine? 4 blinks at a sound signal, such an error is not described anywhere. The machine can not work, immediately gives the end of the program and squeaks 4 times.
The same thing, I can not find.