Error codes for washing machines Electrolux
Fault codes for washing machines are needed to simplify diagnostics.
Using them, we can easily understand what has broken down in our household appliances.
This approach is quite convenient. And so we get down to business.
Codes
| Code | Code Interpretation | Why did the error appear and how to fix it? |
| E11 | Water is not poured into the tank during the execution of programs. The amount of water did not reach the required time. |
|
| E13 | There was a leak. The liquid got into the drip tray. | Make sure that the water is actually in the pan. Find and repair the leak. |
| E21 | Water was not poured out of the washing machine in the set time (10 minutes). |
|
| E23 | The triac of the pump control broke. | Make sure there is a breakdown by checking the triac. If the failure is confirmed - change it. |
| E24 | Violation of the integrity of the triac circuit of the pump. | Make sure there is a breakdown and repair it. |
| E31 | Damage to the level switch. |
|
| E32 | Erroneous data from the pressostat |
|
| E33 | Incorrect or inconsistent functioning of pressure-sensitive sensors (1st level relay and protective relay will heat the element). | Here are the most common options for this situation:
|
| E34 | Mismatch of the data of the level switch and the second level of anti-boiling. | If the error is displayed for more than one minute:
|
| E35 | Excessive amount of water in the machine | There was too much water. It reached its maximum. Check the level switch and, if it breaks, change it. |
| E36 | Damage to the protective relay of the level of the heating element. | Check for malfunction. |
| E37 | The relay of the 1st water level broke. | Check this part. |
| E38 | No pressure change signal (probably pressure switch tubule has clogged) | Clean / change tube. |
| E39 | Overflow pressure switch broke. | Check this device. |
| E3a | Damage to the heater relay. | Need to change. |
| E41 | Insufficiently tight door closure. | Open and close the door again. |
| E42 | Damage to UBL. | Check and, if necessary, change the door lock device. |
| E43 | The UBL control triac broke. | Verify its malfunction and replace. |
| E44 | The sensor opening the door has deteriorated. | Make sure that there is a breakdown. |
| E45 | Broken parts of the circuit of the UBL simistor | Check these parts. |
| E51 | Shorted electric motor triac | Carry out a malfunction check. If it is confirmed - change the broken part. |
| E52 | The motor tachometer does not transmit data to the controller. | One of the most common reasons for the appearance of the E52 code is the missing mounting washer.For this reason, the coil may be displaced and such a malfunction will occur. You can correct the situation by returning the coil and washer in place or changing the tachometer. |
| E53 | Parts of the control circuit of the triac of the electric motor are out of order. | These parts are checked and, if a breakdown is detected, they are replaced. |
| E54 | The contact group of the reverse relay has sunk (a total of 2). | Check and replace the part if there is a malfunction. |
| E55 | Open in motor circuit |
|
| E56 | No data from the tachometer generator. | Change the specified spare part. |
| E57 | Electricity more than 15 amperes. |
|
| E58 | Electricity electric motor is higher than 4.5 amperes. |
|
| E59 | Within 3 seconds from the moment of giving the command about the engine operation, there is no signal from the tachometer. |
|
| E5a | The cooling radiator is heated above 88 degrees. | Replace the electronics box. |
| E5b | The voltage drops below 175 V. | Check the wires. Change the electron. block. |
| E5c | The voltage in the bus exceeded 430 V. | Change the electronics unit. |
| E5d | FCV does not receive / send data for 2 seconds. | Change the electronics unit. |
| Sec | Communication problems between FCV and ch. printed circuit board. | Change the electronics box. |
| E5f | FCV control board makes configuration requests without stopping. Due to the fact that there is a reset all the time. | Perform a wiring test. Replace it if necessary. If all else fails, replace the electronics box. |
| E61 | During heating, the water does not reach the temperature necessary for the execution of the program for the required period of time. | This error appears only in the diagnostic mode of the washing machine. Make sure that the heating element (TENA), its contacts and wires are in good condition. |
| E62 | The water warmed up over 88 degrees in five minutes. | Make sure that the heater is in good condition (there is a possibility that a case breakdown has occurred). But most often this code is displayed at the time of the breakdown of the temperature sensor. The temperature sensor must be tested with a multimeter. If the resistance is from 5.7 kOhm to 6.3 kOhm, then with it everything is in the drift. |
| E66 | A failed relay will heat the element. | Check the wiring, circuit and relay of this part. If something is faulty - change. |
| E68 | Excessive leakage current | Change the heater or other components. |
| E71 | Excessive temperature sensor voltage | Most likely, contact breakage occurred or shorted the sensor and / or circuit. |
| E74 | The temperature sensor is not positioned correctly. | Make sure that he takes a normal position. |
| E82 | Violation in the selected selector location. | The electronics module, wiring or selector has failed. |
| E83 | The signal from the selector is not identified. | This code appears only in the diagnostic mode of the machine. Incorrect configuration, change the block. |
| E84 | The recirculation pump is not identified. | Change the electronics unit. |
| E85 | Recirculation pump failure. | Change the pump or electronics unit. |
| E91 | Communication problems of the interface and the main unit. | It is necessary to change the electronics. |
| E92 | There is a correspondence problem between the main unit and the interface. | It is necessary to change the electronics unit. |
| E93 | Problems with the configuration of the machine. | You must enter the correct configuration code. |
| E94 | Incorrect configuration of the machine and the execution of a given program. | Overwrite volatile. memory, or change the circuit. |
| E95 | Communication problems with volatile memory and processor. | Make sure that the power supply on the board is volatile memory. Check the integrity of the circuit between the EEPROM and the "process". |
| E96 | Mismatch in the configuration data of the electronics controller and connected / unconnected elements. | Check for compliance / non-compliance of the connected elements. |
| E97 | The problem of compliance of the software of the electronics controller and software selector. | Incorrect configuration of the machine is possible. Change the main unit. |
| E98 | The problem of correspondence between the electronics and the control unit of the electric motor. | Carry out a check and, if necessary, change the wiring. Make sure that the electronics unit is working properly. If not, change it. |
| E99 | Incorrect electronics connection and unit sound. | Change unit; check wiring. |
| E9a | Software violation between the electronics and the speaker. | Change the electronics unit. |
| EA1 | Incorrect DSP operation. | Check wiring; you may need to change the main unit; change the DSP; change the drive belt of the engine. |
| EA2 | Problem with DSP identification. | Changing the main unit is required. |
| EA3 | DSP does not lock the engine pulley. | Check and change wiring. Check and change the drive belt of the engine. Change the DSP. Change the main unit. |
| EA4 | DSP is out of order. | Check wiring. Change main unit. Change DSP. |
| EA5 | The DSP is out of order. | Change the main unit. |
| EA6 | The lack of data on the movement of the drum during 30 seconds from launch. | The drum doors are open (at the vertical). It is necessary to change the drive belt of the engine. It is necessary to change the DSP. |
| EB1 | The frequency of the mains does not match the necessary. | It is necessary to conduct a power supply check. |
| EB2 | Excessively high voltage. | Carry out a power check. |
| EB3 | Excessively low voltage. | Check the power supply. |
| EBE | Faulty relay protection circuit. | It is necessary to change the electronics unit. |
| EBF | Problem with protection circuit identification. | The electronics unit needs to be changed. |
| EC1 | The flooding valve has stalled. | Change wiring. Change this valve. Repair / change wiring. |
| EC2 | Failure associated with the sensor responsible for the cleanliness of the liquid. | Change it. |
| Ef1 | Excessively long is the discharge of water from the machine. | Make sure the pump is working. Clean the inlet hose and the entire system. |
| Ef2 | Excessive foaming at the time of draining. Drain hose clogged. Drain pump filter clogged. | Make sure the pump is working. Use only machine washable powders. Do not put too much powder in the dispenser. Clean the pump filter and the drain hose. |
| Ef3 | Water control system activated. Problem with pump wiring. Break in pump. Leakage. | Change the pump. Repair the wiring. Inspect the machine for leaks. |
| Ef4 | No data is received from the flow sensor when the filler valves are activated. | Water intake blocked. Or its absence in water pipes. |
| Ef5 | Emergency stop push-ups due to a significant imbalance in things in the tank. | Make sure that you don’t put more things than recommended for your machine. Make sure that the machine with less laundry is working properly. |
| Eh1 | The frequency of the voltage is not normal. | Electricity problems. Perhaps the electronic components need to be changed. |
| Eh2 | Overstated voltage. | Change electronics. |
| Eh3 | Excessively low voltage. | Change electronic components. |
| Ehe | Faulty relay protection circuit. | Change the electronics unit. |
| Ehf | Problem with protection circuit identification. | Replace the electronics box. |
Interesting:
9 reader comments
Add a comment
Headings
Washing machine repair
For buyers
For users
Dishwasher
I have an EWS 11600 W.Announced the completion of washing a few seconds after starting. An autopsy showed that the wire stupidly dropped from the drain pump. Corrected, of course, easily, but it is unclear why the car did not begin to swear. Glitch firmware, or need special conditions, so that the error appears?
We are knocked out errors E40 and E80 in the list they are not what they mean?
Change the lock.
EF0 - what kind of error? After washing does not go to rinse.
EAO error appeared, what should I do?
It produces an error E 40 each time, what should I do?
Electrolux gives error EF5 drum. Does not rotate. The operation of the drain pump is audible, but the water does not drain. What to do?
Error e 90, what to do?
EWT 815 vertical, lower LED flashes 5 times. What kind of mistake?