All about washing machines

Error codes for washing machines Bosch Logixx 8

Bosch Logixx 8 Error CodesOwners of Bosch Logixx 8 Varioperfect washing machines often come across the fact that their favorite "home assistant" gives out various system malfunctions. When such a breakdown occurs, the machine stops its operation, and a special code is displayed on the display.

To understand what actually broke at the washing machine, you need to decrypt this code, find the reason for its appearance, eliminate this reason, and then test the washer for other breakdowns. This is what we will do, and we will describe the course of our actions in the article.

Self-diagnosis system ciphers

Having carefully studied the instructions for the Bosch Logixx 8 typewriter, we can easily find the error code table of its self-diagnosis system. True, the description of these errors in the instruction is "lame." The manufacturer did not consider it necessary to decrypt all the errors in sufficient detail, so we will do it for him.

  1. Error F 16 indicates that the UBL cannot lock the hatch of the washing machine.
  2. The error number F 17 indicates that the pressure of the water that enters the machine through the inlet hose is too weak. Sometimes this code appears in the absence of water in the water supply.
  3. Error F 18 appears if the pump cannot drain the waste water fast enough. It takes 10 minutes to completely remove water according to the program, if the pump for some reason does not fit in the allotted time, a code appears on the display.
  4. Error number F 19 may occur if there is a problem with heating the water. In this case, the signal from the heating element arrives, but it does not work properly.

The most common cause of error F 19 is a layer of limescale on the heating element.

  1. Error F 20 may occur when the heater starts to heat up spontaneously, and the control module ceases to control this process.error code 0 bosh
  2. An error with code F 23 indicates the appearance of water in the pan of the washing machine and the activation of the Aquastop system.
  3. Error F 25 indicates an error in the water level sensor; in more rare cases, this code indicates a breakdown of the water turbidity sensor.
  4. Errors F 26 as well as F 27 indicate problems with the pressure sensor. On Russian-made cars, such sensors fail very often.
  5. Errors with numbers F 28, as well as F 29 tell us about problems with the solenoid valve, and also with the flow sensor. In more rare cases, these codes pop up on the display at low water pressure in the water supply.
  6. Error F 31 indicates that there is too much water in the washing machine's tank. For some reason, the system cannot draw a predetermined amount of water, but draws too much. Most likely, the pressure switch is to blame.
  7. Errors F 34 and F 36 indicate a physical malfunction of the locking sunroof device. With such errors, the UBL itself is functioning properly, but the locking mechanism does not function well, or the supply cable of the UBL has poor contact.
  8. Errors F 37, as well as F 38 tell about the breakdown of the temperature sensor. F 37 often appears during the breakdown of the sensor, and F 38 when it is de-energized or bad contact.
  9. Error with code F Indicates to the user that the control module is not able to control engine speed. In this case, the control module does not receive the correct signal from the tachometer, which means that the engine starts and runs at maximum speed.
  10. An error with code F 43 indicates that the engine cannot gain speed. In this case, it is very likely that the engine or tachometer is damaged.
  11. Error F 44 tells us that the engine cannot operate in reverse mode. The problem here is not in the engine, but in the control module.
  12. Error F 59 indicates a malfunction of a special 3D sensor, which is responsible for monitoring the power module.
  13. Error number F 60 tells about the breakdown of the flow sensor. The control module system simply stops detecting this sensor. Most likely it burned out.
  14. Error F 61 indicates that the UBL is completely burned out.
  15. More rare errors F 63 and F 67 appear in the event of a failure in the firmware of the control board or if the microprocessor breaks.

service codes for washer Bosch Logixx 8

System Testing for Faults

If system errors then appear, then disappear, a complete testing of the washing machine system for critical malfunctions is necessary. Bosch Logixx 8 is equipped with the appropriate software, you only need to be able to run the general test, and then wait for its results. The test is carried out completely in automatic mode, so there is nothing to worry about.

How to run this same test? Turn on the washing machine. Close the door of the hatch of the washing machine until it clicks. We turn the program switch knob and set it to the “Off” position and wait 2 seconds. We translate the program switching knob to “Spin”. Click and hold the button on which the "Functions" arrow is drawn to the left. We switch the program switching knob to the "Drain" position, until we release the arrow. After 2 seconds, release the arrow.

The display should appear. Once it appears, you can use the arrows to select a test program. There are 17 of these programs and each is responsible for its own unit. Run each one at a time and mark the ones where the system detected a malfunction.

Troubleshooting

If you identify any problems using the self-diagnosis system, it is better not to engage in amateur activity. Especially in cases where the warranty onwashing machine Bosch is still acting. Call the service center and call the wizard, it will certainly help. However, before calling the wizard, you must make sure that there is no local failure in the system, which could also easily generate an error. What should be done?

  1. Turn off the washing machine with a button.
  2. Disconnect it completely by unplugging the plug from the power outlet.
  3. Wait 10 minutes.
  4. Turn on the washing machine again.

If we are talking about a local failure, the machine will reboot completely, the code will disappear and may not appear again. If the cause of the code is a serious breakdown, the machine will soon freeze again and already in this case you need to run to the phone and call the master.

   

Reader Comments

  • Share your opinion - leave a comment

Add a comment

Read also

Error codes for washing machines