Ariston washing machine does not drain

Sometimes when washing clothes, consumers notice that the Ariston washing machine does not drain the water. And this malfunction is quite common in the Hotpoint Ariston model line. There are several reasons for the appearance, and now we decided to talk about what could happen to household appliances, and how to conduct a “painless resuscitation”.

The appearance of a breakdown, its causes

If you start to notice that the washing machine does not drain the water, you need to pay attention to its behavior. First of all, you should understand what manifestations a designated breakdown has. Among the "symptoms" are clearly distinguished such as:

• slow drain, with possible software failure;
• after starting, the wash stops when draining;
• water is drained several times, but not several times;
• when washing everything goes in the standard mode, but at the moment of rinsing the drain stops;
• Spin is not activated at the end of the drain.

What causes a breakdown? The reasons are varied, but in the specific case, the behavior of the washing machine will help determine it. First of all, the technician can issue an error code indicating the nature of the malfunction.

1. The pipe connecting the pump and tank is clogged.
2. The pump is clogged with a small object.
3. The trash filter is clogged.
4. The pump is out of order.
5. A siphon or pipes clogged.
6. The drain hose is clogged.

Cleaning the trash filter

The procedure is carried out in several stages. Even if you have no experience in this matter, you must cope. Well, if you encounter any problem, you can always call the master.

First of all, you need to shut off the water and disconnect the equipment from the power. There is a possibility that you will need to push or lift the machine. And you are unlikely to want to get an electric discharge when the water remaining in the machine flows onto the floor.

In the second step, you should find where the filter is installed, then open the sunroof and remove the bezel. As a rule, the hatch is held by a latch, which you can pry with a flat screwdriver. But there are models where you can open it without an additional tool.

Take rags and drain the remaining water from the machine. In order for sewage to pour out, you should unscrew the filter. And in order not to fill the entire floor, under the body you will need to substitute a small pallet or other flat containers.

In some machines, you will not need to perform the indicated procedure, because water itself drains into a substituted container through the built-in gutter. To completely drain the water, turn the plug of the filter element by 45-60 degrees to the left.

Remove the filter. In this step, you will need to clean and rinse the filter. Large debris is immediately pulled out, and then using a dishwashing sponge, plaque is removed and the filter is washed with water. Along with the above, you will need to clean the filter seat in the machine, using the same dishcloth. In the last step, put the filter back.

Important! It is strictly forbidden to wash the filter with hot water, as this can lead to deformation and a decrease in the elasticity of the gasket!

We clean the drain pipe

According to statistics, most often the drain does not work precisely because of a clogged nozzle. You can get to it exclusively through the bottom of the washer. Models with an open bottom are equipped with a nozzle that is brought out. You just need to put the equipment on its side, and the pipe will become visible. But models that have a pallet or bottom cover, require their removal, after which access to the pipe will open again. The washing machine Ariston, or rather its pipe has three connection points: tank, pump, pressure regulation hose.

The first task is to loosen the pipe clamps at each connection point. After it, you only need to move it to the side.In situations where the condition of the pipe is satisfactory, cleaning is carried out using a special brush. They can be thoroughly cleaned and then returned to the original position. But with severe wear or serious damage, you will need to replace it by installing it on existing mounts.

Interesting! It is possible to carry out high-quality cleaning of the nozzle with a solution of citric acid. To prepare it, you need to take 2 liters of water, dissolve 100 grams of lemon in it, and then place the pipe in the resulting liquid for several hours. After the part will need to be removed and thoroughly washed with cold water.

Drain pump

If the problem is still relevant and the water is still not drained, you will need to go to the next step. Within its framework, we need to check the pump, or rather find out if the impeller is jammed. It is located right behind the filter, and if even a small object (for example, a rivet from clothes) is inside it, this can cause a breakdown.

In view of the foregoing, at the initial stage, you need to try to scroll the impeller. When it is spinning, and there are no foreign objects, it is working. But in reverse situations, you will need to immediately remove an extraneous thing. If this does not solve the problem, check the drain pump electrician.

For these purposes, removes the filter, guided by the above instructions. After we set the spin mode and highlight the filter hole. To do this, a small flashlight or flash phone. When the impeller is stationary, this is clear evidence of a broken pump. So, a malfunction has already been found, and we need to go to the next step - installing a new component.

But before you replace the drain pump, you will need to buy it. The design of most washing machines includes standard parts, so that we can easily purchase the one that suits us at the nearest home appliance store or on the construction market. And if the points of sale are located at a decent distance from your home, you can go to the expanses of the World Wide Web and find the right component in online stores.

So, the item was purchased, and the time has come to install it. To do this, dismantle the drainage unit and disconnect the drainage pump from it. Then, with special attention, we remove all wiring from it, take the purchased part and make a replacement. We return all wiring and other details to their original position, and then collect the Hotpoint Ariston washing machine in its original state.

At this stage, the question: what to do with a non-working discharge, is completely disassembled. And you can easily restore the efficiency of the equipment yourself at home using the instructions provided.