DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » »Tesla Transformer on Kachera Brovina from 220 volts
In this article I will talk about how to make Kachrov Brovina relatively small power with the same set of parts. So what is a “kacher”, in essence it is a kind of Tesla coil, which I am a resonant transformer with which you can get a huge high-frequency voltage and therefore a strong electromagnetic field that has quite interesting properties. And so we will leave the words and move on to the installation assembly process itself.
But of course, before you assemble, you need to understand how it works and what it is assembled from.
Here is the installation diagram.


The circuit is powered by a 220 V network voltage, which, before going directly to the main generator part, is rectified through the D1 diode and lowered by means of a choke, I used a 12 volt transformer which is turned on by a 220 winding, in other words, we take two wires to which the network is connected to the transformer 220 and one of them is also connected to 220 and the second goes to power quality to capacitor C1. Now let's move on to the resistors, R2 you can use medium power, I used the Soviet medium size, as for R1, I just didn’t have such a charge and I used 4 to 12 KOhm of high power and all the resistors remained cold even after a long work. Now let's touch the transistor with the most scarce part of the installation. KT828 can be taken only as a last resort if it is not possible to get imported ones, namely the Panasonic transistor C5244A showed excellent work but don’t repeat my mistakes, don’t try to remove the throttle or set it very small, in my case I removed it altogether and the transistor exploded quite slightly. You can use 2SA1943 and similar voltage and current parameters, the transistor, as usual in these cases, is placed on the radiator.
Here is all the electronics.


We solder everything according to the scheme and that's what I got
 

Now the main part is not very technological and terribly boring part. We wind the coil L1 (primary) With a copper wire, a diameter of at least 5 mm About 5 -7 turns, the diameter of the coil is about 14 cm.

 
Now, what many do not undertake to assemble such installations for is winding L2 (secondary) Plastic pipe with a diameter of 5 cm, a height of 25-30 cm is possible enough if patience is enough. I wound two coils with wire of different diameters
The first is 0.2-0.3 wire and 25 cm high.


And with a diameter of 0.5-0.8 mm To a height of 35 cm.


(The light on the left is just a lamp. This is not a quality effect)
All the same, they managed to get more effect from the second coil, due to obviously more area.

And now we actually collect as in the photo above and below.


The first start (if everything works) do not delay, start for 1-2 minutes and see how the transistor and other parts are heated so as not to overheat them during prolonged operation.
Do not try to touch all metal parts; it is life threatening!
So it all worked for me the first time I turned it on, if everything is done correctly, you will have the same thing. If not. Change the ends of the primary, check if the transistor and diode are "alive"
Now, actually, for the sake of what we have all done, the effects that can be obtained
1. Corona discharge
This is a discharge that comes off the free end of the secondary which should be pointed, it is better to take the needle. It looks very beautiful, purple crown. A corona discharge creates the so-called electric wind, i.e. you can notice a small breeze smelling of ozone, on this effect the so-called "ion engine" is going. If you touch the discharge with your finger there will be no pain. As a high-frequency current passes over the surface of the skin, some sources say that it has a vasodilating effect and it’s almost a panacea that saves from all diseases, I personally haven’t noticed anything except a tiny burn and a little smoke from my finger. But Nikola Tesla, who actually discovered the high-frequency current and subjected his body to discharges, lived to be 86 years old. But I still do not advise abusing such experiences. Yes, and the discharge begins to come out of the knife in the hand, if you bring it to the coils of the secondary. Also, the discharge does not have a small temperature, lighter gas easily ignites in the vicinity and you can even make a thin sheet of paper smolder.

 
The camera does not convey the beauty of this phenomenon.
2. HF Field
We are talking about the electromagnetic field that surrounds the kacher, this is a high frequency field. In fact, it does not do anything magical. Although it may be “uninitiated” this will seem like a miracle. If you take a discharge lamp in your hand, bring it to the quality, it will light up in your hands and quite brightly, I could easily light two lamps with a power of even 36W, while the effect of certain stripes was observed in the lamp, it looks pretty pretty, (for those who dreamed of play star wars)
Here is the lamp at 18W


4x6W
 

Lighting, two on 18W

Also, by the means of the same field, one can demonstrate the effect of the transmission of electricity to a distance without wires. For this, another coil is required, preferably with exactly the same parameters (number of turns, wire cross-section, etc.) in this case, a much better effect can be achieved. We assemble the backup coil and install the same as the radiating coil. The difference is that a diode bridge is connected to the outputs of the primary
 

It is necessary to take high-frequency diodes, due to the fact that I couldn’t find any at hand, I could not verify this effect, but there was a voltage in the secondary, discharges that could be pulled out of the understudy spoke about this.
That's actually all I wanted to say about this device.

The author does not bear any responsibility for your life and health, the voltage of 220V is life threatening, it is recommended that you read the safety precautions before assembly. It also has a harmful effect on the RF field surrounding the kacher. I advise you to take breaks.

 Wishing to repeat good luck!

come back
Comments (69)
  1. kisli4
    #51 kisli4 Guests December 3, 2013 18:57
    0
    Please help, I assembled according to this scheme, the transistor put 2t839, I turn on, the spark jumps off the secondary, and the transistor burns right away, I reassembled but the effect is the same, there is a spark and the transistor breaks right there
  2. Timorfy
    #52 Timorfy Guests January 25, 2014 13:38
    0
    Quote: stepan
    ... not so much a hole due to non-observance of the proportions of the windings ???? Please tell me!

    Actually, yes, I did it too. I wound my first coil on cardboard twisted into a tube almost a meter high and 7-8 centimeters in diameter. From it, neon lamps glowed in half a meter, and incandescent in 20 centimeters.But cardboard lit up at high humidity and I rewound to PVC. And then many miracles disappeared. There is a lot of my video on assembly and demonstration on timorfy dot ru.
  3. Michael
    #53 Michael Guests February 11, 2014 09:14
    0
    Interested in what current this device consumes? measured? no? at least about ... thanks in advance ... with respect. Michael.
  4. jeka
    #54 jeka Guests May 7, 2014 9:19 p.m.
    0
    which diode to take?
  5. Dmitry
    #55 Dmitry Guests September 8, 2014 18:04
    0
    Please tell me if the diameter of the pipe on which you wind the secondary and where to connect the lower contact of the secondary on the second circuit matters
  6. Egor
    #56 Egor Guests November 7, 2014 19:24
    0
    I did not understand, but which diode is needed?
  7. Maksim
    #57 Maksim Guests July 15, 2015 19:11
    0
    My wire is covered in black paint. Is this suitable for the secondary?
  8. edward44
    #58 edward44 Guests November 18, 2015 21:55
    0
    [b] paxich2 [/ b],
    Well, the capitalists, it doesn’t work out? Knowledge and reason do not exist?
    As I understand it, you are a genius in your country, you even know about oil transformers. Have you ever wondered what sizes they are? )))
    No brother, don’t even try. What even children do here, your academics have never dreamed of!
  9. edward44
    #59 edward44 Guests November 18, 2015 22:12
    0
    Boys - take the diode from the microwave - you won’t be mistaken
  10. Vitalj321
    #60 Vitalj321 Guests May 21, 2016 18:39
    0
    Guys, what inductance should a choke be? (At least throw a picture, so that you know exactly which one.) I do not trust the transformer after an unsuccessful event.
    I have two transistors: 2SA1943 and 2SC5200. I think the first to use. Diode - D248b. The capacitor is the same as in the circuit.
    And nothing will happen if the secondary is wound on a pipe with a diameter of 2.5 cm?
  11. lotos
    #61 lotos Guests June 15, 2016 23:10
    0
    First turn on the brain, and then spend the money.
  12. Sergey
    #62 Sergey Guests June 23, 2016 01:29
    0
    I collected everything strictly according to the scheme, WORKS, but I don’t see the crown. I wonder why?
  13. Vladimir
    #63 Vladimir Guests 10 January 2017 11:58
    0
    [b] Veent [/ b],
    Tell me, can I solder the wire if it is short, so that the L2 coil is larger?
  14. Cat
    #64 Cat Guests March 3, 2017 20:57
    0
    And if you use a 9 volt transformer?
  15. Magianauka magianauka
    #65 Magianauka magianauka Guests April 16, 2017 15:50
    0
    the circuits are rather capricious and when using a throttle we get a nice stove my circuit works from 110 volts and the power is several times greater.
  16. SanSanych
    #66 SanSanych Guests September 28, 2017 17:28
    0
    Circuits with transformerless undervoltage using chokes and zener diodes are dangerous. It is not surprising that the transistor exploded ... they are usually at 25 volts. Do not risk your life ... Use batteries, batteries or power supplies with transformers.
  17. Guest Roman
    #67 Guest Roman Guests January 9, 2019 17:11
    0
    And what does an average power resistor mean? How much is a watt?
  18. Guest Roman
    #68 Guest Roman Guests January 21, 2019 04:40
    0
    The wire to which 220 volts is connected on the transformer goes directly to the outlet, and the second, to which 220 volts is also connected, goes to the capacitor. And then it makes sense to put a transformer?
  19. Guest Roman
    #69 Guest Roman Guests January 25, 2019 07:51 AM
    0
    One wire of the transformer goes to phase, and the second to minus the capacitor?
Load more
1 2

Read also

Error codes for washing machines