DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » »Browin Kacher and Tesla Transformer
Kacher - a device that generates a high voltage (5000-20000 volts) of high frequency. Do not be afraid - you will not be shocked. This is not the same current as in the outlet - it has a high frequency (up to 250 kHz), but in our outlet it is 50 Hz. At a high frequency, current flows through the surface of your body.
The simplest circuit is shown in Figure 1. In order to assemble this circuit, you will need a minimum of parts that can be found in old TVs:

Browin Kacher and Tesla Transformer


1.2 resistor
2. 1 transistor transition p-n-p (it must be powerful and high-frequency, for example
ct805. See the catalog)
3. 1 Capacitor
4. Copper wire 0.15 - 0.25 mm (can be purchased at the radio store or by unwinding any power transformer)

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer


We buy or unscrew resistors from any radio boards. You can also remove the capacitor from the circuit boards. The transistor can also be unscrewed from the board - they are usually mounted on radiators. Pay attention that the transistor has a pnp junction, if there is an npn junction, you need to change the collector and emitter with the connection points. What can be said about the radiator, then it should be large, and if you do not have a large radiator, then install a cooler on the small radiator. We take out copper wire from any transformer.

Browin Kacher and Tesla Transformer


Now proceed to the assembly:
We take a tube from cardboard and wind the secondary winding coil to coil wire (0.15-0.25) periodically pouring varnish. This is the most painstaking work. The more turns, the better the final result. Now around the secondary winding we make 3-4 turns with a thicker wire (wire, plate) whose thickness (width) should be 1-4 mm. Next, we connect these 2nd windings to the circuit and connect this device to the network. And what do we see? When a fluorescent lamp is brought to this device, it burns without wires ... We can conduct electricity through the body without harming any organ, for this it is enough to put a hand to the secondary winding and with your other hand grasp tightly to one of the contacts of the fluorescent lamp ...

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer


Note: If the device does not work, then turn over the primary winding, i.e. the magnetic fields of the windings must match. If you wind one winding clockwise, then the second should be wound in the same way.

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer

Browin Kacher and Tesla Transformer
come back
Comments (71)
  1. wefl
    #1 wefl Guests December 7, 2012 23:56
    1
    and what is the diameter of the secondary and the current consumption (to select a transformer
  2. V.A.L.E.K.
    #2 V.A.L.E.K. Guests December 8, 2012 10:50
    0
    cool mego cool
  3. Veent
    #3 Veent Guests December 11, 2012 18:10
    4
    Everything is fine, only the npn transistor is shown on the circuit as well as the ct 805 is npn and not pnp. And so it’s not bad)
  4. 79519778830
    #4 79519778830 Guests December 22, 2012 21:50
    0
    cool but i don't know how to wind 1000 turns
  5. nikoko
    #5 nikoko Guests September 16, 2013 13:40
    0
    What is the current consumption ???
  6. Sergey
    #6 Sergey Guests November 11, 2013 14:43
    1
    And what is the power?
  7. Ivgen
    #7 Ivgen Guests February 8, 2014 03:37
    0
    And where is the socket, if the battery is drawn on the diagram ... smile
  8. Andrei
    #8 Andrei Guests March 5, 2014 13:25
    1
    You can draw anything on the diagram, but the transformer can be the source of food, although Akum on a kacher FITS BETTER! The secondary winding can be reeled in as much as desired (optional) at least 500 turns! CONSUMPTION CURRENT 12 VOLTS}:) !!!!! Kacher turned out super! I like!!! I give a big plus !!! +++++++++++++++++++++++++ !!!! and recommended vkontakte article laughing !
  9. Znatok
    #9 Znatok Guests March 6, 2014 19:14
    0
    But is the bta06 600c transistor suitable?
  10. Vladimir
    #10 Vladimir Guests March 7, 2014 17:15
    4
    Quote: Andrew
    You can draw anything on the diagram, but the transformer can be the source of food, although Akum on a kacher FITS BETTER! The secondary winding can be reeled in as much as desired (optional) at least 500 turns! CONSUMPTION CURRENT 12 VOLTS}:) !!!!! Kacher turned out super! I like!!! I give a big plus !!! +++++++++++++++++++++++++ !!!! and recommended vkontakte article laughing !

    Actually, the current is measured in amperes.
  11. Andrei
    #11 Andrei Guests March 8, 2014 21:08
    0
    Quote: ZnatOK
    But is the bta06 600c transistor suitable?

    This is a teristor, so it won’t do!
  12. WHITENIGGER
    #12 WHITENIGGER Guests March 24, 2014 21:55
    1
    A 600 WIRES OF 0.10MM WIRE ON A 4CM TUBE WILL SUIT?
  13. Sergey
    #13 Sergey Guests June 18, 2014 13:10
    1
    Turns should be at least 1000 and no more than 2100. Better more))) More turns - more voltage at the output, the thickness parameters of the secondary wire cross section affect the output amperage, the thicker the higher the amperage (minus the thicker the larger the coil, and the greater the supply energy is secondary). Now the primary: the less the higher the frequency (range 3 - 5 turns) it is better to make the primary one thick - ideally a copper tube from the conder (we put sand into the tube by thunder, solder, heat, bend). Then we feed the ground to the primary and increase the charge in this way. We hook the fan to the triode for cooling And that’s it. Then we take one wire (preferably thin) at one end we hook to the end of the secondary (where there is a coronary discharge), and at the other end we solder 2pcs diodes, one direct, the other backward (diode bridge) to these diodes, we hook the bulb (very small ) or an LED and a voltmeter. Turn it on. We find a theoretical physicist to try to explain this. (For those who do not know: the current does not flow in this closed circuit, but in theory it is impossible to read physics and scoff at theorists.
  14. Alexander
    #14 Alexander Guests June 22, 2014 01:02
    1
    Can you explain to me which is better to take a capacitor?
  15. Andrei
    #15 Andrei Guests July 21, 2014 20:53
    0
    Quote: Vladimir
    Quote: Andrew
    You can draw anything on the diagram, but the transformer can be the source of food, although Akum on a kacher FITS BETTER! The secondary winding can be reeled in as much as desired (optional) at least 500 turns! CONSUMPTION CURRENT 12 VOLTS}:) !!!!! Kacher turned out super! I like!!! I give a big plus !!! +++++++++++++++++++++++++ !!!! and recommended vkontakte article laughing !

    Actually, the current is measured in amperes.

    And you give 12 amperes to this circuit and the transistor will die !!!!
  16. Alex
    #16 Alex Guests August 24, 2014 20:49
    1
    and the p702 transistor will do
  17. Alex
    #17 Alex Guests August 26, 2014 21:52
    0
    and from the crown the coil will work
  18. Alex
    #18 Alex Guests August 30, 2014 23:07
    1
    question to the AUTHOR, the transistor is round or rectangular, and which is better suited to kt805am or kt837n and make a copper perich from copper or zinc
  19. Matveyka141
    #19 Matveyka141 Guests September 23, 2014 17:14
    2
    But is 2t903b suitable?
  20. Alex
    #20 Alex Guests September 29, 2014 16:44
    1
    is that a transistor?
  21. Alex
    #21 Alex Guests September 29, 2014 16:51
    0
    I think there is no need powerful as kt805
  22. Alex
    #22 Alex Guests September 29, 2014 16:55
    0
    I think that no one is needed as powerful as kt805 or others: what:
  23. Matveyka141
    #23 Matveyka141 Guests September 29, 2014 20:41
    0
    damn it, and then I have no others ((: recourse:
  24. Matveyka141
    #24 Matveyka141 Guests September 30, 2014 20:59
    0
    Quote: Alex
    I think that no one is needed as powerful as kt805 or others: what:

    But what transistor did you use? In my opinion, the picture does not show CT805
  25. Matveyka141
    #25 Matveyka141 Guests October 1, 2014 20:17
    0
    But is kt805am rectangular?
  26. Alex
    #26 Alex Guests October 3, 2014 9:38 p.m.
    0
    yes kt805am rectangular is much better only if everything is done correctly, I have a secondary tube 3cm in diameter and 37cm high and everything works
  27. Alex
    #27 Alex Guests October 3, 2014 9:39 p.m.
    0
    oh sorry tube it's a pipe
  28. Matveyka141
    #28 Matveyka141 Guests October 4, 2014 10:52
    0
    Quote: Alex
    yes kt805am rectangular is much better only if everything is done correctly, I have a secondary tube 3cm in diameter and 37cm high and everything works

    Thank you so much!
  29. Matveyka141
    #29 Matveyka141 Guests October 4, 2014 12:19
    0
    for some reason does not work
  30. Matveyka141
    #30 Matveyka141 Guests October 4, 2014 20:43
    0
    no, everything works, it was just necessary to increase the wire diameter, but for some reason the sparks are very small, barely noticeable: recourse:
  31. Vitaliy
    #31 Vitaliy Guests October 17, 2014 09:35
    0
    Capacitor written 0.1 - why, farad?
  32. Alex
    #32 Alex Guests October 18, 2014 17:30
    0
    yes 0.1 farad but what kind of food?
  33. Basil
    #33 Basil Guests November 2, 2014 00:43
    0
    I recommend the resistor capacity 2.2kom to adjust the adjustable resistor to 10kom so it will be possible to adjust the size of the sparks
  34. Basil
    #34 Basil Guests November 3, 2014 10:57
    0
    Oh! I apologize for the disinformation, instead of a 150 ohm resistor, it is necessary to set an adjustable up to 1 room
  35. Basil
    #35 Basil Guests November 3, 2014 20:34
    0
    I used the kt819a transistor primary 4 turns of 1.5mm secondary 0.1mm 1400vit battery 12v 3 ampere capacitor 56 picofarad resistors those on the circuit. Thanks to the author for the circuit!
  36. Lyokha
    #36 Lyokha Guests November 25, 2014 17:09
    0
    Which capacitor is 0.1 microfarad or picoforad
  37. Den
    #37 Den Guests December 9, 2014 9:07 p.m.
    0
    Quote: Lyokha
    Which capacitor is 0.1 microfarad or picoforad

    Microfarad read comments
  38. PSYCHO
    #38 PSYCHO Guests December 21, 2014 14:34
    0
    Is the kt604 transistor suitable?
  39. Salavila
    #39 Salavila Guests December 29, 2014 00:32
    0
    and I only have large irfs630b? can something be done with it?
    In general, a wick and a glow with how many volts start? And then I wound up in a twisted pair, there it is 1 mm thick, respectively 200 turns per 20 cm 40 mm fanina, this is somewhere 333 megahertz it turns out a quarter wave. And I also want to get into resonance.
  40. PSYCHO
    #40 PSYCHO Guests December 30, 2014 15:57
    0
    And kt846 will do? And a 1000 microfarad capacitor?
  41. transistor
    #41 transistor Guests February 7, 2015 18:19
    1
    But is kt805dm suitable?
  42. transistor
    #42 transistor Guests February 7, 2015 18:47
    0
    But can a resistor not 150th but 100th?
  43. Sasha
    #43 Sasha Guests February 12, 2015 20:37
    0
    ANALOGUES OF TRANSYUK KT805:
    -KT905A
    -BD123
  44. the guest
    #44 the guest Guests April 8, 2015 06:37
    0
    Thank you so much for your article! Only at your place I saw: “If the device does not work, then turn the primary winding over, that is, the magnetic fields of the windings must match. If you wind one winding clockwise, then the second should be wound in the same way.” If it weren’t for you, I wouldn’t have guessed !!!!
  45. SB3V4
    #45 SB3V4 Guests April 8, 2015 12:53
    0
    Please tell me, can I use the ST13007 transistor for this installation?
  46. Anton
    #46 Anton Guests May 25, 2015 16:52
    0
    It is said that you need to take a pnp transistor, and the diagram shows an npn transistor (the same ct805)
    And even further it is said that if you take the npn transistor, then you need to change the collector and emitter in places, but if I take the ct808a, then I need to solder everything as in the diagram, or do I swap the number and emr? I'm confused! kt808a npn transistor!
    HELP ME PLEASE!!!!!!
  47. mario
    #47 mario Guests May 30, 2015 12:05
    1
    Anton, you do not need to swap the collector with the emitter, this is a mistake, but you just need to change the polarity of the power supply. So the design can use transistors of both conductivity, observing the polarity of the power supply.
  48. Maksim
    #48 Maksim Guests July 15, 2015 19:10
    1
    I did not work. True, I have a secondary wire in black paint. Isn't that the problem?
  49. ilya
    #49 ilya Guests July 18, 2015 15:43
    0
    Which of these transistors can be used here? KT829A KT858A KT818A KT940A
  50. Kuzyma
    #50 Kuzyma Guests August 20, 2015 08:12
    0
    [b] ilya [/ b],
    any, given the polarity of the source depending on the conductivity, for example: kt818 - p-n-p and is controlled by a "minus" relative to the emitter.

Read also

Error codes for washing machines