DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » »Manual generator with ionistors for starting the engine
Using this drive with manual recharging, you can start the car engine when the main battery is low. In addition, this device can power various inverters with loads, LED lamps, charge smartphones, etc. It does not require maintenance and is always ready to go.
This drive has two huge advantages:
  • It is equipped with a hand-held generator, with which you can fully charge it anytime, anywhere.
  • Second, the device is built on ionistors (supercapacitors), and they, unlike rechargeable batteries, do not require any maintenance, are capable of discharging to zero, they are tolerant at low temperatures. Therefore, such a thing can be thrown into a secluded place and it will lie there until it is needed, and as needed, it will be accurate ready for the loads.

Hand generator with ionistors for starting the engine

Will need


  • Handheld Generator 1500 mA (20 W), Purchased at .
  • A bar with 6 ionistors and a balanced protection bar, also purchased on .

In general, it can, of course, be assembled separately, by first purchasing supercapacitors and a protection board.
For the case used thick plywood fastened with self-tapping screws.

We collect the drive with manual recharging


So let's get started. According to the size of the board, we determine the dimensions of the future case.
Hand generator with ionistors for starting the engine

Next, we cut out all the parts on the machine or manually with a hacksaw.
Hand generator with ionistors for starting the engine

We drill a hole under the generator and fix it.
Hand generator with ionistors for starting the engine

We assemble the side parts of the body.
Hand generator with ionistors for starting the engine

The handle was included, screw it onto the shaft.
Hand generator with ionistors for starting the engine

Be sure to connect the generator to the ionistors through the diode and check whether charging is in progress. Do not reverse the polarity if you intend to repeat something like that.
Hand generator with ionistors for starting the engine

The charge is on. We’ll plug a cigarette lighter socket into the side wall so that other consumers can be fed.
Hand generator with ionistors for starting the engine

We turn on the cigarette lighter parallel to the entire battery, also pay attention to the polarity carefully.
Hand generator with ionistors for starting the engine

To check, insert a USB converter and a 5 Volt LED bulb into the USB socket.
Hand generator with ionistors for starting the engine

Everything works without problems. Now the input is a more capacious load: the connected inverter is loaded with an electric drill, with which we drill holes for screws in the same case.
Hand generator with ionistors for starting the engine

The top cover is made of transparent plexiglass. The terminals are screwed on it like a car battery. Solder wires from them to supercapacitors.
Hand generator with ionistors for starting the engine

And close the lid, fixing everything with screws.
Hand generator with ionistors for starting the engine

Test


Charge the battery to full.
Hand generator with ionistors for starting the engine

This will take about 3-7 minutes. The generator provides approximately 1.5 A in load. By the way, it is not possible to charge capacitors with a voltage of more than 15.8 V, since the balanced protection board works well. At the same time, when this or that section is fully charged, then on the opposite side of it, on the board, the LED lights up.
Hand generator with ionistors for starting the engine

Remove the old battery from the car.
Hand generator with ionistors for starting the engine

We put our drive.
Hand generator with ionistors for starting the engine

The car is launched without unnecessary difficulties. With ionistors it is quite possible to ride without reinstalling the battery.
Now consider other uses. We already talked about the inverter with a drill. About the 5V bulb too.
Hand generator with ionistors for starting the engine

But how long will it burn?
Hand generator with ionistors for starting the engine

Over an hour! And it still shines well. You can charge the phone at the same time.
Hand generator with ionistors for starting the engine

And if you insert an extra bright 12 V flashlight into the socket?
Hand generator with ionistors for starting the engine

That will turn out a super flashlight.
Hand generator with ionistors for starting the engine

Watch the video


come back
Comments (7)
  1. Vita
    #1 Vita Guests April 26, 2019 06:27
    0
    To increase the voltage, a capacitor is connected in parallel with the winding, the type depends on the shape of the output signal. Does this fact affect the operation of the circuit.
  2. Guest Vlad
    #2 Guest Vlad Guests April 26, 2019 2:36 p.m.
    6
    something wiring is too thin for a starter needed as a minimum section of 4mm. I really doubt that it will give a starting current of 250 amperes ??? !!! all this is not serious ..
    1. Nikola
      #3 Nikola Guests 11 june 2019 15:17
      1
      You probably wanted to say 40 mm2
  3. Vitaliy Ivanovich
    #4 Vitaliy Ivanovich Guests April 26, 2019 16:13
    0
    The idea is just super. You are well done!
  4. Guest Valery
    #5 Guest Valery Guests April 27, 2019 8:16 p.m.
    1
    Dear Author! Can I use ionistors to create a magnetization - demagnetization device? I'm going to make a magnetic motor
  5. Al
    #6 Al Guests May 25, 2019 11:13
    0
    It is necessary to install not one diode, but a diode bridge. And why such a huge box, if it is empty. Probably you can pick up the balancer more compactly and generally put two rulers. Well, as already noted, the wires are too thin, which is fraught with fire.
  6. Nick
    #7 Nick Guests July 29, 2019 10:15
    0
    what is the capacity of the ionistors.

Read also

Error codes for washing machines