DIY do it yourself
Master classes, instructions, useful tips, recipes.
» »How to make a sawmill from improvised materials
Not everyone has the financial ability to purchase a factory-made power-saw bench for households. But if you look around, you can find a lot of materials from which you can assemble a home-made sawmill.
Perhaps there will be some costs with the purchase of an electric motor (a second-hand, but serviceable one) and circular saws will do, but still they will be much less than the cost of a factory sawmill.

Homemade power-saw bench design


How to make a sawmill from improvised materials

It will be a frame construction of rectangular pipes and corners, providing sufficient rigidity and strength. Initially, a belt drive was planned from the electric motor to the ring saw drive pulley, but then this option had to be abandoned due to its complexity and lack of reliability.
In the final version, the drive pulley (wheel assembly from a passenger car of size R13 or R14 with a fully inflated tire) was rigidly mounted on the motor shaft.
How to make a sawmill from improvised materials

The driven pulley selected exactly the same wheel mounted on a movable carriage, with which it is possible to adjust the tension of the circular saw.
How to make a sawmill from improvised materials

This design of pulleys along which the circular saw moves solves two important tasks:
  • stability of the cutting tool during operation is ensured, that is, the saw does not slide off the pulleys due to the large friction force between the rubber and the metal of the tool;
  • random peak loads are extinguished, for example, when the saw passes through the knot zone, due to the elastic properties of the rubber.

Bearings are mounted in pairs vertically behind the drive wheel and in front of the driven wheel, between which the descending branch of the hole saw passes, which dampens its vibrations and gives it direction.
How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

The lifting mechanism is assembled on the basis of a cable winch and two pulleys.
How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

Using it, you can raise or lower the cutting unit and, thereby, adjust the thickness of the resulting board and raise the saw at the end point to return the cutting unit to its initial position.
How to make a sawmill from improvised materials

So that the racks of the cutting unit can easily move in the rails, and there is no play, in them 4 bearings are welded on top and bottom on the axes.
How to make a sawmill from improvised materials

Also made a simple knot of tension of the circular saw based on adjustable traction, removed from old agricultural machinery.
How to make a sawmill from improvised materials

The cutting unit, together with a saw, a winch, an electric motor, a driving and driven pulleys (wheels), moves on 4 rollers along two longitudinal corners, placed angle to the top on a reliable base.
How to make a sawmill from improvised materials

Sawmill at work


Serving a home-made sawmill in the process of dissolving a beam or a small round log in diameter on the boards is not difficult.
The sequence of basic operations is as follows:
1. The cutting unit is installed in its original position, so that the working (lower) branch of the circular saw is located up to the opening array, which must be securely fixed to prevent its longitudinal and transverse movement.
2. Using a cable winch, raising or lowering the cutting unit, set the thickness of the board, which is required.
How to make a sawmill from improvised materials

3. A small amount of water is supplied to the lower branch of the cutting tool in the cutting zone, but a soap solution or diesel fuel (preferably less due to rubber damage) is better to cool the saw and extend its service life.
4. The electric motor is turned on, the moving lower branch of the saw is brought to the end of the array, which, together with the cutting unit, manually moves along the guides from the beginning to the end of the cut.
How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

5. At the end of the passage, the board cut off from the array is removed, the cutting unit with a winch rises up and returns to its original position. The device is ready for use again.
To prevent the circular saw from sliding off the driven wheel, a bolt is installed on the carriage, with which you can change the direction of the axis of the driven pulley to a small extent, and thereby counter the saw to go sideways.
How to make a sawmill from improvised materials

Result:
How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

How to make a sawmill from improvised materials

Boards are even and smooth.

Summary remark


For the safety of persons managing such a makeshift sawmill, a circular saw should be enclosed in a protective casing in case it ruptures and prevents splinters from injuring people.

Watch the video


come back
Comments (1)
  1. Prorokparadise
    #1 Prorokparadise Guests April 29, 2019 19:03
    4
    yab and didn’t come to this zombie crusher for a cannon shot, it will break the canvas and fly to the one who is less fortunate

Read also

Error codes for washing machines