DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » »How to check the water meter yourself and why you need it
Once I changed the water meters in my apartment, the time has come so to speak. He didn’t change himself - he called a locksmith from the housing and communal services. He replaced, it means everything seems to be as it should: water runs the meter believes there are no questions. A month later, the time came to take readings and then a bad surprise awaited me: the amount of water consumed per month was almost twice as much as usual! It seems that no one poured - I thought ... Although, maybe someone from home forgot the tap or something like that ... I waited another month - the same story. And here I was specifically thinking. It was unprofitable to call a specialist to check the meter with the device, since all this is not free, and not cheap in 15 minutes of operation. I decided to check the problem counter myself.
How to check the water meter yourself and why you need it

Personally, I know only three ways to check the water meter, this:
The first method: check with a special device. This is only for specialists.
Second: suitable for those who have additional counters. That is, you hang another similar meter on the tap, pass a certain amount of water and then compare the readings of one device with another. Almost like the first method, but the usual counter.
And the third way that I used. It is very simple and accessible to absolutely everyone. Will not require scarce appliances or appliances. Very fast and efficient.

Will need


  • Measured container, in the role of which you can use a three-liter jar, a bottle of water, a canister. The main condition is that with it you can accurately measure the allowable volume of water. In an extreme case, you can use the balance to control the water in the tank, instead of divisions, since 1 kilogram of water is equal to 1 liter (1 cubic decimeter).

DIY water meter check


The technology is this: first of all, you need to choose one tap from which we will take water. I chose a faucet that was in the bathroom - it’s easier to place a container there. And other consumers of water of this highway need to be blocked in order to avoid an error. In my case, I temporarily shut off the tap valve on the toilet drain tank.
Now place the container under the tap. We notice the initial readings of the water meter.
How to check the water meter yourself and why you need it

The dial shows liters, the final right digit is units of liters, the second is tens.
Next, open the tap and drain a certain amount of water. In my case, I used a 10 liter bottle.
Turn off the tap and check the readings. If the meter shows more or less than 10 liters - the device is lying.
How to check the water meter yourself and why you need it

I re-check the normal device, so that everything is "top-to-bottom".
The most important thing! You must do two identical checks. One on an unhealthy water pressure when the trickle barely runs. And the other - on the maximum open tap.
How to check the water meter yourself and why you need it

How to check the water meter yourself and why you need it

Ideally, both checks should show one result.

The result of my checks


As a result of my checks, the counter almost doubled the readings! And all this in the second test, when the crane was opened as much as possible. With a thin stream showed everything almost correctly.
I called that locksmith and explained the whole situation to him. He took off the counter and set it back. And lo and behold - everything began to work as it should!
It turns out that this bad person (radish) during the first installation of the meter lost the gasket included in the kit (there are two of them, they are inserted into the connecting drives). And he cut himself like a pair of scissors from rubber. Set it to the counter input. What is there, you think? The fact is that the locksmith, when he cut the gasket, narrowed the inner hole in it. As a result, with a large pressure of water (when the tap is maximally open), a jet stream was formed, and hit directly on the counter impeller. As a result, it spun twice as fast.
Like this! I never would have thought that this could be so. So, friends, if you suspect something suspicious with your metering devices - be safe and check them yourself.
come back
Comments (5)
  1. Guest Michael
    #1 Guest Michael Guests March 28, 2019 8:13 p.m.
    2
    "... temporarily shut off the tap valve on the toilet barrel" - sounds like a spell. I mean, gibberish. What does “tap valve” mean if “tap” and “tap” are two different types of plumbing fixtures? And what kind of "barrels" of the toilet are we talking about?
  2. Guest Alexander
    #2 Guest Alexander Guests March 28, 2019 9:44 p.m.
    9
    ... since 1 kilogram of water is equal to 1 liter (1 cubic meter). 1 cubic decimeter !!! A 1 cc meter, it is 1000 liters.
  3. Guest Alexander
    #3 Guest Alexander Guests March 28, 2019 9:52 p.m.
    3
    since 1 kilogram of water is equal to 1 liter (1 cubic meter). There is a problem, 1 liter = 1 cubic meter. decimeter! And in 1 cube meter - 1000 liters.
  4. Gennady
    #4 Gennady Guests March 29, 2019 19:16
    0
    I came across one more unpleasant effect: a meter in a well on the street (private house), a 50 mm street pipe was cut into a 600 mm trunk. When the water is turned off for a long time, the main one is filled with air, then they give water, the air is compressed, it exits in the houses with force through any open tap, and the meters spin at a furious speed, spinning virtual cubic meters for which they require real money.
  5. Guest Sergey
    #5 Guest Sergey Guests April 2, 2019 2:58 p.m.
    0
    At the entrance there is a plastic mesh, it should disperse this stream *

Read also

Error codes for washing machines