DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » »How to make a power regulator for household appliances
How to make a power regulator for household appliances

Everyone can assemble such a simple regulator. Knowledge of electronics is not required, since a ready-made Chinese module will be used, which can be purchased for a very small amount. With all this, the controller is able to regulate the power of devices up to 2000 watts.
You can use the regulator to adjust the power of any electric heaters, various engines, power tools, etc.

Will need


  • Junction box.
  • Sleeve for wire.
  • A wire with a plug.
  • Power socket.
  • Regulator board .
  • Small screws.

Power controller manufacturing


Disassemble the junction box by removing the top cover.
How to make a power regulator for household appliances

We take the outlet and also disassemble.
How to make a power regulator for household appliances

Unscrew the side mounts so that they do not hang out. They will no longer be useful.
How to make a power regulator for household appliances

There is nothing more to do with the outlet on this.
How to make a power regulator for household appliances

In the cover of the junction box, drill a hole for the outlet.
How to make a power regulator for household appliances

We install the socket in this socket and fix it with screws.
How to make a power regulator for household appliances

On the side in the box with a step drill, make a hole for the wire sleeve.
How to make a power regulator for household appliances

We insert the sleeve and fasten with plastic nuts on both sides that come with the sleeve.
How to make a power regulator for household appliances

We pass the wire through it.
How to make a power regulator for household appliances

Now it's time to plug in the module. This is not complicated, here is the diagram:
Module connection

To the screw terminals we connect the stripped wires of the network wire. And also we fasten a piece of wire to connect to the outlet.
How to make a power regulator for household appliances

We connect the wires to the contacts of the outlet.
How to make a power regulator for household appliances

With a step drill, we drill a hole on the other side of the box under the variable resistor of the module board. He will hold the entire board in the case.
We insert a variable resistor into the hole, fix it with a nut.
How to make a power regulator for household appliances

We put the handle on the shaft.
How to make a power regulator for household appliances

Close the lid of the box, collect the socket.
How to make a power regulator for household appliances

We screw the sleeve, thereby fixing the wire.
How to make a power regulator for household appliances

Screw the four box screws. The regulator is ready for this.
How to make a power regulator for household appliances

Checking the operation of the regulator


Turn on the network, connect the light bulb. Everything is regulated very smoothly, without any jumps and steps.
How to make a power regulator for household appliances

We try to connect the grinder.
How to make a power regulator for household appliances

How and where to use it, I think it’s not difficult to come up with: electric stoves, heating elements of water heaters, pump motors, etc. A useful and necessary thing in everyday life.
Friends, follow all safety requirements. The tension that is present inside is life threatening.

Watch the video


come back
Comments (11)
  1. Guest Alexander
    #1 Guest Alexander Guests June 18, 2018 10:54 p.m.
    5
    For a load of a resistive type is suitable. For engines, no.
    1. Guest Alex
      #2 Guest Alex Guests June 19, 2018 10:51
      0
      Why?
    2. Guest Michael
      #3 Guest Michael Guests June 20, 2018 3:02 p.m.
      0
      And what, do you think, in the grinders with the regulator are other dimmers? Exactly the same.
    3. anvar
      #4 anvar Guests June 20, 2018 15:37
      1
      by the way the output current is not a sinusoid
      1. Sergey K
        #5 Sergey K Visitors June 21, 2018 13:12
        0
        So in a Bulgarian is a commutator motor, he doesn’t give a damn about a sine wave!
  2. Guest Yuri
    #6 Guest Yuri Guests June 19, 2018 5:06 p.m.
    0
    Bullshit is for nichrome bulbs
  3. Anvar Aminov
    #7 Anvar Aminov Guests June 20, 2018 15:49
    0
    non-sinusoidal current shape
  4. Guest Michael
    #8 Guest Michael Guests June 21, 2018 09:58
    1
    It would be nice to know the characteristics of this device. Judging by the appearance, it is suitable only for devices of low power. Like, in the light bulb diminish-add.
    1. Guest Michael
      #9 Guest Michael Guests June 21, 2018 14:45
      0
      The power of the regulator depends only on the applied triac and radiator in case of heavy load.
  5. Guest Andrey
    #10 Guest Andrey Guests June 21, 2018 19:03
    1
    What is a wire sleeve? I know the seal, the pressure seal. And it works like a dissertation. The pump will not work, it will burn, it's not a frequency converter
  6. Anton
    #11 Anton Guests October 30, 2018 2:23 p.m.
    2
    You can put the regulator board from the vacuum cleaner, just for motors.

Read also

Error codes for washing machines