DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » »Balancing charger for Li-ion
Now the market is full of chargers. Automata and not, with and without capacitance measurement. Most chargers are universal and can charge elements of any chemistry. Lithium ion and lithium polymer are increasingly being used in different devices.
Not so long ago, I remade a screwdriver’s battery into 18650 lithium-ion cells. I charge it with a Turnigy smart charger. But not everyone has this charger.

It will be required for assembly


I decided to assemble a simple charger with a balancer for lithium-ion. The charger has 3 identical independent channels. They can be charged from one element to three. If necessary, you can add any number of channels. I have three of them, that is, 3S or 11.1 volts.
The case for the balancing charger is the case from the burned-out D-link router. If possible, take a larger case, it turns out to work very closely in it.
Balancing charger for Li-ion

One of the main component are the power supplies of each channel. Their role is performed by the tablet charger boards with a 5 Volt output and a current of 1 Ampere (or you can buy on Ali Express - .
Balancing charger for Li-ion

Charge controllers are boards from China - . On each channel, its own controller. I have a board without protection, but in this case it is not needed. You can use the controller boards along with the connectors, I do not have two on them, they were removed for other projects. The price of these modules is cheap. If you are engaged in the development of devices based on lithium-ion and lithium-polymer, then these controllers are indispensable.
Balancing charger for Li-ion

Making a balancing charger


The charge controller boards need to be soldered to the outputs of the charge boards. It is possible and separately. I soldered to thick wires from the power cable, so the design is more rigid.
Balancing charger for Li-ion

On the boards of the charge controllers there are LEDs that indicate the charge and the end of the charge. They need to be removed. Instead, they will be ordinary LEDs, in different colors. They will be attached to the windows where the router LEDs blinked before.
Balancing charger for Li-ion

I soldered wires to the LEDs from the old plume of the computer hard drive. If there are LEDs with a common anode (plus), then it is better to use them. I didn’t have such, I applied what is.
Balancing charger for Li-ion

In place of the old LEDs, solder the cables with LEDs. In the photo I have a green 3 mm LED. I had to replace it, they turned out to be singed, I did not check it before wiring.
Balancing charger for Li-ion

For the back panel you need to cut the trim. In it, we make cuts for the power switch and the 4-pin output connector. The connector was removed from the old hard drive. You can apply any, to the desired number of pins, with a current of 1-2 Amps.
The switch was removed from the old computer power supply. We fasten the cover to two screws, for rigidity.
Balancing charger for Li-ion

Glue the output connector onto epoxy glue or soda with super glue. I glued one and the other for speed.
Charging board with controllers glued to thermo glue. But before fixing, I soldered the network wires.
Balancing charger for Li-ion

One of the network wiring, soldered to the switch. The second, directly to the second wire of the power cord.
Balancing charger for Li-ion

Now glue the LEDs. I glued thermo glue, you can and soda with super glue.
Balancing charger for Li-ion

Solder the output jumpers.
Plus the first controller on the first leg of the output connector. Minus it to the second leg and connect with the plus of the second controller. And so on.
Balancing charger for Li-ion

We twist the case and set it aside.
Balancing charger for Li-ion

Let's make a wire for this charger.
I applied two pieces of wires from a computer power supply. I soldered in order from the first contact of one connector to the contact of the second.
Balancing charger for Li-ion

We connect the charger to the battery of the screwdriver (Alteration of a lithium screwdriver battery) The red LED indicates the ongoing charge process. At the end of the charge, the green LED lights up. Accordingly, the icons on the case light up: Wi-Fi, second and fourth computers.
Balancing Charger for Liion

Here we have a charger. Costs are minimal, and the benefits are great.
With this device, you can charge assemblies on lithium polymers, those that are used by modelers in their vehicles. The main thing is to make the right charging wire.
Balancing Charger for Liion

Watch the video


come back
Comments (0)

Read also

Error codes for washing machines