DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » »Simple microwave welding machine
A simple welding machine for electric arc welding can be done by everyone at home, without the use of any specialized equipment or circuits. All we need is just two microwave ovens, which can be found in a landfill or two transformers from them.
Microwave welding machine

We disassemble the microwave and pull out the transformers.
Microwave welding machine

These step-up transformers, that is, they convert 220 volts to a voltage of the order of 2.5 kV, necessary for the operation of the magnetron. Therefore, the secondary winding in them contains a less thick wire and with a large number of turns. Such a transformer has a power of about 1200 watts.
To assemble a welding machine for arc welding, we do not have to disassemble the core of these transformers. We just cut and drill the secondary high-voltage winding. Usually this winding goes from the top, and the primary one at 220 V from the bottom.
The tool we need to work.
Microwave welding machine

Do-it-yourself simple microwave welding machine


We take the transformer and fix it so that it does not move. We take a hacksaw for metal and cut off the secondary winding on both sides of both transformers. If you decide to repeat, then be careful not to damage the primary winding.
Microwave welding machine

Microwave welding machine

Microwave welding machine

Then we drill the winding with a drill with a drill for metal, thereby removing the internal stress of metals, so that it is easier to knock out the residues.
Microwave welding machine

Microwave welding machine

Microwave welding machine

We knock out the remnants of the winding.
Microwave welding machine

We got two transformers with 220 V windings. The transformer from the left, above the winding, has a current shunt separating the windings. To increase power, they also need to be knocked out. Such manipulation will increase the power of the transformer by 20-25 percent.
It also happens between large windings a small low-voltage winding from a pair of wires - we also throw it away.
Microwave welding machine

We take a stranded wire in plastic insulation with a cross section of six squares and a length of 11-12 meters. You can take a more stranded wire, not coarse as in my example.
Microwave welding machine

Microwave welding machine

I wound about 17-18 turns on each transformer, 6 rows high and 3 layers thick.
Microwave welding machine

Microwave welding machine

Microwave welding machine

Microwave welding machine

Microwave welding machine

The windings are connected in series. I wound everything with one wire, but you can wind each transformer individually, and then connect it. The whole winding is very dense, should not hang out.
Microwave welding machine

After winding is completed, we connect the high-voltage windings to 220 V in parallel. I used car lugs with heat-shrink insulation.
Microwave welding machine

I plug the entire structure into the network, and measure the voltage on the secondary, which I wound. It turned out about 31-32 volts.
Microwave welding machine

Then I took a wooden board and screwed both transformers with self-tapping screws to make a single unit.
Microwave welding machine

When welding, I will use 2.5 mm electrodes and cook two pieces of iron 2 mm thick.
Microwave welding machine

Microwave welding machine

Here is the result.
Microwave welding machine

Microwave welding machine

Microwave welding machine

In principle, you can cook, but not for long, because the transformers are very hot and therefore after each electrode you need to allow the device to cool.
There is enough current, so cooking thin metal does not work out very well, since it just cuts. To reduce the current in the circuit, you can use a choke or a balanced resistor. In the role of a resistor, you can take a piece of steel wire, incorporating it into the low-voltage winding circuit, and select the current by its long length, adjusting the evenness of the arc burning.
I am satisfied with the result, it will fit perfectly for domestic needs, taking into account the fact that I actually got everything for free.

Watch the video of making an arc welding machine


come back
Comments (2)
  1. Guest Sergey
    #1 Guest Sergey Guests June 10, 2018 5:05 p.m.
    3
    Put transes in the case and make forced cooling-it will be possible to burn 3-4 electrodes in a row;)
  2. Guest Valery
    #2 Guest Valery Guests February 10, 2019 12:30
    0
    Take a thicker wire, and add another transformer by installing it in a case with forced cooling, you can cook even longer, and with a thicker electrode ...

Read also

Error codes for washing machines