To work on the product you will need:
- a newspaper.
- PVA glue.
- blue acrylic paint.
- polymer glue "Titan".
- red and green foamiran.
- scissors.
- knitting needle.
- stamens and a wide semi-bead.
- 3 green and golden leaves.
- strip of floristic grid.
-wire.
- a piece of crepe paper.
- a thin synthetic ribbon for natural flowers of gold color.
- foil.
- a brush.
And let's start by making a paper heart. We cut strips 2.5 cm wide from the newspaper. We take a knitting needle and glue P A A and begin to wind the strips on an iron base, fixing with glue. Then we simply pull out the spoke. Glue one tube to the wire and do not remove it. From this tube, we bend the shape of the base of the heart 10 cm high and 13 cm wide. And then we fix the remaining tubes in a chaotic manner around the base. We begin twisting from the lower acute angle in the heart.
Then with a brush we paint the finished heart-base of the composition with blue acrylic paint and give time for complete drying.
Meanwhile, we draw fantasy flower patterns. Based on the circle, draw a flower with 6 petals. And such circles will be with a diameter of 7.5 and 6.5 cm, and small ones of 5 cm.
According to the patterns, we cut out two large blanks and 2 smaller ones from red foamiran.
On two large petals we draw with the tip of the scissors veins starting from the middle of the workpiece.
Then we change the material structure of all 4 blanks. Alternately fold the petals in half 3 times and scroll the folded corners of the blanks with your fingers. Then we open the petals back, it turns out a soft fabric, unlike paper.
In two large petals, we also scroll in the middle of the workpiece. Petals are already voluminous.
Now you need to collect the middle of the future flower. Take ready-made stamens and half beads.
To the underside of this bead, glue in a circle stamens, 1.5 cm long.
The details are ready and proceed to the assembly of the fantasy flower. The first floral circle will be a blank of 7.5 cm. Toward its middle, glue the second large part, staggering the petals, and fix the half-bead with stamens to the center of this blank. The flower is ready.
It remains to secure two green leaves from the wrong side.
We still have two small blanks and from them we will make 2 buds. We cut two wires of 6 cm each and from the foil we form droplets 1 cm high. We fix the foil to the wire and take one red blank.
We pierce the part and put the foil in the center of the workpiece. The petals are raised one by one and glued to the base.
We arrange in a circle. Each petal goes to the middle of the previous one. The bud turns out to be closed, and we will have two of them.
But they lack sepals. Therefore, from the pieces of green foamiran we cut 6 long triangles, 4 cm high.
Green blanks should also be fully scrolled with your fingers. Add 3 together and process.
Then glue the resulting leaves down the buds.
Now let's start assembling the composition on the newspaper heart. From a thin synthetic tape we tie a loop for hanging.
And now we collect all the details for decoration. We have a flower and two buds, three gold leaves and 1 green, a 2 cm wide strip of mesh, a small artificial twig and a golden synthetic ribbon.
All jewelry will be mounted on one half of the heart. The first to fix a strip of mesh in the form of an eight and a thin ribbon folded in half.
Then we glue the branch to the middle of the decoration with a downward inclination.
Now we glue two buds downward of the flower, bending the wire in small loops.
Now we fix this flower with buds in the middle of the composition, but we direct the buds up to the loop. Then, on these buds from the bottom, glue the remaining green leaf.
The remaining golden leaves are located under the flower, directing in different directions.
The center of the composition should be the main flower, and all other details should be close around it.
Perhaps the location may be a little different, it all depends on your taste.
Good luck to all!
