- 2 types of fabric (basic with a bright floral pattern) and finishing (bright red color), the fibrous composition of the fabric can be any,
- synthetic winterizer (density not more than 150 g / sq. m),
- threads
- lightning 35 cm long,
- lightning 18 cm long,
- a small piece of a dense transparent film,
- red rep ribbon (width about 1 cm, length 50 cm),
- white lace of two kinds (in the form of braid and in the form of flowers),
- pieces of felt yellow and bright pink flowers,
- duct tape,
- scissors
- chalk or soap for cutting,
- sewing machine,
- iron.
The manufacturing process of an organizer bag consists of 3 main steps:
1. Preparation of the pad.
2. Harvesting top.
3. Installation of the product.
Blank blank.
For a bag measuring 30 * 30 cm and a thickness of 15 cm, a lining with a size of 77 * 47 cm should be cut out. From all angles, the width of the lining should be cut by 3 cm, starting from the end cut and leading to “no” after 30 cm.
On the lining of the bag, it is necessary to process numerous and various pockets that meet the requirements of the customer. For example, if the needlewoman is interested in knitting, it is advisable to make pockets for hooks and knitting needles, for various little things (loop counter, centimeter tape, pins). Some pockets can be fastened with buttons, others with adhesive tape or a buttonhole - it all depends on what will be stored in them. If desired, some pockets can be decorated with decorative braid in the form of flowers - the product should look aesthetically pleasing both outside and inside. In addition to pockets made of fabric, you can also make pockets of dense transparent plastic. Its source may be, for example, packaging from under any trifles for needlework. The main thing to remember is that the more diverse the pockets are, and the more they will be in the bag, the more convenient the needlewoman will use it, and the needlework process itself, organized as well as possible, will bring her sincere joy and pleasure.
The prepared lining must be sewn along the sides, and then the corners should be stitched so that the width of the bottom of the bag is 15 cm.
Harvesting top.
The top of the bag will consist of 3 parts, - the main part and 2 finishing strips. The latter are cut out of the finishing fabric, their width in a cut is 12 cm.
The size of the base of the bag should be equal to the size of the pad. The prepared base of the bag should be stitched on a synthetic winterizer. It must first be ironed on both sides through a cotton cloth at maximum iron temperature. Heat treatment will contribute to the compression, compaction of synthetic winterizer. It will become more rigid and resilient, lose softness and airiness. But this is exactly what is needed - inserted into the bag, this material will give it shape stability. Next, you need to cut out the handles of the bag, as well as a folding pocket with a zipper. The handle of the bag in a cut will represent a rectangle with dimensions of 8 * 108 cm (2 pcs.), The detail of the pocket is a rectangle of 17 * 20 cm (2 pcs.).
Handle parts should be folded along face inwards and stitched 1 cm from the cuts, turned out and ironed. Harvested handles need to be sewn with end slices between each other.
Details of a pocket with a zipper must be cut with corners rounded on one side. They must be folded facing each other, enclosing a zipper in two longitudinal and one transverse sections and stitched with a 7 mm wide seam. Then the part of the pocket must be turned out, ironed, along the edge to lay the finishing line.
After all the parts have been prepared, you need to process the internal pockets in the pocket with a zipper.They can be made of fabric, as well as of dense film, so that their contents can be seen. Immediately you can sew a needle bar made of felt made in the form of a pillow, make several loops of tape for hanging small things.
Then you need to process the pocket with a zipper at the same time as the straps of the bag.
The prepared top of the bag must be sewn along the sides in a similar way to the hem and stitched in the corners.
Installation of the product.
Installation of the product consists in connecting the lining of the bag with its top. To do this, the lining should be placed in the upper part face to face and sewn along the upper cut. In one place you need to leave a plot for turning out - it does not need to be sewn up. After this, the bag must be unscrewed, the hole sewn. Then, on top of the bag, lay the finishing line. If desired, the edges of the bag can be ironed. The temperature of the iron should be low so as not to spoil the film and plastic pockets in the bag.
The product is ready. You can fill it with tools and get to work.
