DIY do it yourself
Master classes, instructions, useful tips, recipes.
» » » »Fursi hairpin made of satin ribbons
A wide palette of shades of satin ribbons allows you to create charming jewelry. The right combination of several tones allows needlewomen to create quite realistic flowers for various ornaments.

Fursi Satin Ribbon Hairpin


To clamp the “Fursi” you will need:
- long hair clip.
- sharp scissors.
- satin weave ribbons of three different shades: green, lilac and light pink.
- beads for weaving pink.
- cotton pads.
- glue gun with a spare rod.
- wire for needlework.
- lighter.

A step-by-step description of creating hair clips.
The hairpin consists of one main flower and three small unblown buds. Each part is made separately and consists of a certain number of petals.
Start work with the preparation of the petals. To do this, from the ribbons of pink and lilac shades, it is necessary to cut two types of parts. The size of large blanks is 6x4.5 cm. The parameters of small ones are 4.5x4.5 cm. Large rectangles need to be cut out only from lilac ribbon, their number is 15 pieces. Small details should be prepared from two shades of ribbons, pink will need 6 pieces, and lilac 10 for the main flower and 15 for the buds.
Now the upper edge of the rectangles needs to be made rounded, and the lower slice to be narrowed on the sides. The result is raw petals of two sizes.

make round


Now using the flame of a lighter, all parts will need to be carefully scorched from all sides, evenly stretching at the rounding points, giving them a wavy appearance.

using flame lighter


Cotton pads should be cut in half.

Cotton pads


Having prepared a wire 10 cm long, you need to fix its edge in the middle of a half of a cotton pad.

Having prepared the wire


The remaining edge of the disk must be wrapped around the wire and fixed in this state with glue. The result is a kind of umbrella.

wrap around the wire


A pink petal is carefully glued to this umbrella, but only the top edge of the part needs to be attached.

glued pink petal


Then 2 more pink petals should be attached, gradually placing them around the cotton pad. Then the lower sections of all parts must be tightly attached to the wire, so that a closed bud is obtained.

need to tightly attach


The two remaining petals also stick to this bud, but now glue should be applied only to the lower cut, so that the bud turns out to be magnificent.

stick to this bud


It turns out here is such a bud, repeating the whole sequence, you need to create three more of the same flowers from lilac small blanks. Five buds are required for each bud. A lilac flower will serve as a center for the main inflorescence.

Next, around the pink petals, you need to attach 10 lilac details of a small size.

bud


Then glue large petals around the circumference. This will form the main flower.

large petals


Further on the base of each flower, it is necessary to fix the sepals made of green ribbon.

fasten sepals


Bead loops are an additional decoration for hair clips. To create them on a wire you need to pass pink beads. The length of the stitches can be different from 3 to 5 cm.

hairpin decoration


Then green ribbons need to cut large triangles and make them leaves for flowers. In total, 5 pieces will be required.

cut big triangles


From the resulting leaves, it is necessary to glue the fan, carefully laying the tips of the parts on top of one another.

glue fan


A green strip 3 cm wide is fixed to the bottom of the fan, which will serve as the basis for the hairpin.

green stripe is fixed


On top of the leaflets are fixed two buds directed in different directions.

two buds are fixed


The third bud is located on the other edge of the base.

Third bud


Near a single bud, bead loops are attached, two pieces on each side.

bead loops attached


Now, in the center of the remaining space on the base, a large flower is glued.

Fursi Satin Ribbon Hairpin


It remains to turn the jewelry over and securely fasten the hair clip along the base line.

hairclip


Fursi hair clip is completely ready!
come back
Comments (0)

Read also

Error codes for washing machines