For work, we need:
- skewers.
- corrugated paper: pink, hot pink, raspberry, white.
- board.
- glue gun.
- mesh.
- beads.
- silver paint.
- foil.
- scissors.
- threads.
Let's start by preparing the basics for the fan. The base of the fan will be skewers.
We take white paper and cut into strips 10x1 cm in size, cut strips across the fibers. And stretch it to the limit. We will wrap it and tighten the skewer. Using a glue gun, glue the paper to the skewer. We need 12 pieces of such pasted skewers.
We begin the assembly of the fan. To do this, glue two skewers at an angle of 45 degrees. Let the glue dry. We glue everything well so that it does not come off later.
Thus, glue the remaining skewers.
Now that the glue based on the fan has dried, we will need to glue the places where the skewers are glued together. To do this, take a strip of white paper measuring 5x1 cm, stretch it to the limit and tighten the bottom of the base to cover the traces of gluing skewers.
Now that the base is ready, we will decorate it. To do this, take the beads. They will also be 12. Take a bead and glue it on the sharp tip of the skewer. As if we put a bead into a skewer.
We also process all beads with skewers.
Now it's time for the flowers that will be an ornament for our fan. Rose petals will be of two sizes. The first - which are smaller, will be 8x5 cm, the second - 10x8 cm. For one rose, we need 5 small and 3 large.
We begin to give the petals a new shape. Cut the upper corners in a semicircle.
With a knitting needle or skewer we twist the semicircular edges of the petal. With our fingers we make a depression in the middle of the workpiece. But we do not touch one small petal; it remains without twisted edges.
Thus, we process all the blanks we need.
Take this untreated petal and stretch its middle. This will be the middle of the flower. Now prepare the inside for our middle.
Take a foil measuring 10x30 cm, and crush it into a ball. This will be the filling for the middle of the flower. Instead of foil, you can take a more delicious filling, for example, round candies. Then the fan will be not only a beautiful, but also a very tasty gift.
Take our ball of foil and put in the middle of the base.
Then we carefully turn the base, making a pointed corner at the top.
Take the thread and tightly tie the edge of the base, under the ball.
And cut the bottom edge of our petals. Making the lower edge whiter round. And now, using the glue gun, we attach the petal to the base.
We fix the next petal to our base.
Glue all the remaining small petals.
And then we attach and all the large petals. Well, our flower is ready. In the same way we make the rest of the flowers. Light pink we will need 4 flowers. There will be 5 bright pinks. Raspberry need 2 pieces.
Now it's time to draw a skewer base into a beautiful fan. To do this, we need a gray mesh with shiny inserts. The mesh will be 30x30 cm in size.Cut off an even square. But we do this very carefully so that it does not begin to crumble.
First, glue the mesh on the bottom of the base of the fan. Glue the mesh to the fan well. And let the glue dry.
Pull the mesh a little and thread skewers with beads into the mesh holes. And glue the mesh to each skewer. Then when everything is glued and dried, carefully cut off the unnecessary edges of the mesh that protrude beyond the edges of the fan.
Now it's time for the board. It will be 35x10 cm in size. We clean the surface and apply silver paint on top. We are waiting for the paint to dry. And only then we proceed to further work.
We fix the fan on the board as follows. The edge of the fan extends slightly beyond the board. And attached to the back of the board. Leaving ahead a place for the arrangement of flowers.
Take 1 raspberry and 2 light pink flowers and glue them together. Leaving a raspberry flower in the middle.
Now we attach these flowers to the fan and the board.
Then gradually glue the remaining flowers. In order one by one.
Thus, we fix the remaining flowers, except for one.
And the last remaining flower is fixed on the fan. Cut a little mesh, insert a flower into the hole. Glue the mesh with a flower on all sides. Let the glue dry. The flower will be fixed on top of the fan. Between the first and second skewers.
On the opposite edge of the board, from the flowers, glue a bead.
And also attach the beads to the flowers. Creating unique elegance to our fan. OK it's all over Now. Our wonderful fan is ready.
Good luck to all.
